Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

DTC    B2275    STSW Monitor Malfunction

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction is detected in the starter circuit inside the power management control ECU.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2275
Power management control ECU internal HV activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*)
  1. AM2 fuse
  2. Steering lock system
  3. Power management control ECU
  4. Wire harness or connector
Turn the power switch on (IG) and wait 10 seconds or more, then start the hybrid control system 3 times.
  1. *: Only detected while a malfunction is present.

Vehicle Condition and Fail-safe Function when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Function when Malfunction Detected
  1. The power source mode changes to on (READY) even though the hybrid control system is not started.
  2. The power source mode does not change to on (READY) even though the hybrid control system is started.
-

WIRING DIAGRAM


B293336E01


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  4. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.


HINT:

Related Data List and Active Test Items 
DTC
Data List Item
Active Test Item
B2275
Power Source Control
  1. Starter Request Signal
-

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Turn the power switch on (IG).

  1. After 25 seconds have elapsed, check if the DTC has been set again.

    OK:
    DTC B2285 is not output.



NG
GO TO DTC CHART (DTC B2285) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B223988E07
  1. Disconnect the I3 and I4 connectors from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I3-1 (AM22) - Body ground
    Power switch off
    11 to 14 V
    I4-7 (AM21) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)
B223988E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-5 (E01) - Body ground
    Always
    Below 1 Ω
    I3-6 (E1) - Body ground
    Always
    Below 1 Ω
    I4-4 (E12) - Body ground
    Always
    Below 1 Ω
    I4-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)