POWER DOOR LOCK CONTROL SYSTEM > All Doors LOCK/UNLOCK Functions do not Operate Via Door Control Switch or Door Key Cylinder |


| 1.CHECK DOOR LOCK OPERATION |
Check door lock operation (Click here).
| Result | Proceed to |
| All doors cannot be locked through multiplex network master switch | A |
| All doors cannot be locked through driver door key cylinder | B |
|
| ||||
| A | |
| 2.CHECK DTC OUTPUT (LIN COMMUNICATION SYSTEM) |
Clear the DTC (Click here).
Recheck for DTCs.
|
| ||||
| OK | |
| 3.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Replace the multiplex network master switch assembly (for TMMK Made) (Click here).
Replace the multiplex network master switch assembly (for TMC, TMMR Made) (Click here).
| NEXT | |
| 4.CHECK DOOR LOCK OPERATION |
Check that all doors can be locked and unlocked by using the multiplex network master switch assembly (Click here).
|
| ||||
| OK | ||
| ||
| 5.READ VALUE USING INTELLIGENT TESTER (DOOR KEY-LINKED LOCK AND UNLOCK SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Door Key SW-Lock | Driver door key-linked lock/unlock switch lock signal/ON or OFF | ON: Driver door key cylinder turned to lock position OFF: Driver door key cylinder not turned to lock position | - |
| D Door Key SW-UL | Driver door key-linked lock/unlock switch unlock signal/ON or OFF | ON: Driver door key cylinder turned to unlock position OFF: Driver door key cylinder not turned to unlock position | - |
|
| ||||
| OK | ||
| ||
| 6.INSPECT FRONT DOOR LOCK WITH MOTOR ASSEMBLY (for DRIVER DOOR) |
Remove the front door lock with motor assembly (for driver door) (for TMMK Made) (Click here).
Remove the front door lock with motor assembly (for driver door) (for TMC, TMMR Made) (Click here).
for LHD
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 9 (L) - 7 (E) | Locked | Below 1 Ω |
| 9 (L) - 7 (E) | off | 10 kΩ or higher |
| 10 (UL) - 7 (E) | Unlocked | Below 1 Ω |
| 10 (UL) - 7 (E) | off | 10 kΩ or higher |
| *a | Component without harness connected (Front Door Lock with Motor Assembly LH) |
| *b | Unlock |
| *c | Lock |
for RHD
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (L) - 8 (E) | Locked | Below 1 Ω |
| 6 (L) - 8 (E) | off | 10 kΩ or higher |
| 5 (UL) - 8 (E) | Unlocked | Below 1 Ω |
| 5 (UL) - 8 (E) | off | 10 kΩ or higher |
| *a | Component without harness connected (Front Door Lock with Motor Assembly RH) |
| *b | Unlock |
| *c | Lock |
| Result | Proceed to |
| OK | A |
| NG (for TMMK Made) | B |
| NG (for TMC, TMMR Made) | C |
|
| ||||
|
| ||||
| A | |
| 7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK WITH MOTOR ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) |
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K1-9 (L) - I13-11 (L2) | Always | Below 1 Ω |
| K1-10 (UL) - I13-24 (UL3) | Always | Below 1 Ω |
| K1-7 (E) - Body ground | Always | Below 1 Ω |
| I13-11 (L2) - Body ground | Always | 10 kΩ or higher |
| I13-24 (UL3) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| J1-6 (L) - I13-11 (L2) | Always | Below 1 Ω |
| J1-5 (UL) - I13-24 (UL3) | Always | Below 1 Ω |
| J1-8 (E) - Body ground | Always | Below 1 Ω |
| I13-11 (L2) - Body ground | Always | 10 kΩ or higher |
| I13-24 (UL3) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||