AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST |
| DATA LIST |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Vehicle Speed | Vehicle speed/ Min.: 0 km/h (0 MPH), Max.: 255 km/h (158 MPH) | Actual vehicle speed |
|
| Engine Speed | Engine speed/ Min.: 0 rpm, Max.: 16383 rpm | 600 to 700 rpm: Idling (shift lever in P, engine warmed up and A/C off) | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| Calculate Load | Load calculated by ECM/ Min.: 0%, Max.: 100% | 20 to 40%: Idling with warmed up engine |
|
| Coolant Temperature | Engine coolant temperature/ Min.: -40°C (-40°F), Max.: 140°C (284°F) | 75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Intake Air Temperature | Intake air temperature/ Min.: -40°C (-40°F) Max.: 140°C (284°F) | Equivalent to temperature at location of mass air flow meter sub-assembly | This is the intake air temperature.
|
| Engine Run Time | Engine run time/ Min.: 0 sec., Max.: 65535 sec. | Time after engine start | This is the time elapsed since the engine was started.
|
| Battery Voltage | Battery voltage/ Min.: 0, Max.: 65.5 V | 11 to 14 V: Idling | If 11 V or less, the characteristics of some electrical components may change. |
| BATT Voltage | Battery voltage/ Min.: 0 V, Max.: 79.998 V | 11 to 14 V: Idling | If 11 V or less, the characteristics of some electrical components may change. |
| Throttle Position Sensor No.1 Voltage % | Absolute throttle position sensor No. 1/ Min.: 0%, Max.: 100% |
| The No. 1 throttle position sensor output is converted using 5 V = 100%.
|
| Starter SW | Starter signal/ OFF or ON |
| - |
| Neutral Position SW | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Stop Light SW | Stop light switch status/ ON or OFF |
| - |
| Complete Parts Monitor | Comprehensive component monitor/ Not Avl or Avail | - | Avail: The monitor is available on the vehicle. Not Avl: The monitor is not available on the vehicle. |
| TC terminal | TC terminal Status/ ON or OFF | OFF | - |
| MIL | MIL status/ ON or OFF | OFF | - |
| MIL ON Run Distance | Distance driven with MIL on/ Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | - | This is the distance driven since the MIL was illuminated |
| Running Time from MIL ON | Running time from MIL on/ Min.: 0 minute, Max.: 65535 minutes | Running time since the MIL illuminated | - |
| Time after DTC Cleared | Time after DTCs cleared/ Min.: 0 min, Max.: 65535 minutes | Time elapsed since DTCs cleared | This is the time elapsed since the DTCs were cleared (or the vehicle left the factory). Time elapsed after the engine switch is turned off is not counted. |
| Distance from DTC Cleared | Distance driven after DTCs cleared/ Min.: 0 km (0 mile), Max.: 65535 km (40723 mile) | Distance driven since DTCs cleared | This is the distance driven since the DTCs were cleared (or after the vehicle left the factory). |
| Warmup Cycle Cleared DTC | Warm-up cycles after DTCs cleared/ Min.: 0, Max.: 255 | - |
|
| OBD Requirements | OBD requirement/ - | EOBD (Euro-OBD) | - |
| Number of Emission DTC | Emissions-related DTCs/ Min.: 0, Max.: 127 | - | This is the number of emissions-related DTCs. |
| Total Distance Traveled | Total distance traveled/ Min.: 0 km (0 mile), Max.: 16777215 km (10425361 mile) | - | - |
| Total Distance Traveled | Total distance traveled/ Min.: 0 km (0 mile), Max.: 27000309 km (16777992 mile) | - | - |
| NT Sensor Speed | Input turbine speed/ Min.: 0 rpm, Max.: 12750 rpm |
| Data is displayed in increments of 50 rpm |
| NC Sensor Speed | Counter gear speed/ Min.: 0 rpm, Max.: 12750 rpm | - | Data is displayed in increments of 50 rpm. |
| Shift SW Status (P Range) | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (S Range) | S mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | Park/neutral position switch status/ ON or OFF |
| When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| A/T Oil Temperature No.1 | ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 150°C (302°F) |
| If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted. |
| NT Sensor Voltage | Input speed sensor NT output voltage/ Min.: 0.000 V, Max.: 4.999 V | 0.1 to 1.9 V | - |
| NC Sensor Voltage | Output speed sensor NC output voltage/ Min.: 0.000 V, Max.: 4.999 V | 0.1 to 1.9 V | - |
| Lock Up Status | Lock up/ ON or OFF |
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th, 5th or 6th | Same as actual gear | - |
| Solenoid (SLT) | Shift solenoid valve SLT status/ ON or OFF |
| - |
| Solenoid (SLU) | Shift Solenoid valve SLU Status/ ON or OFF |
| - |
| Solenoid (SL1) | Shift Solenoid valve SL1 Status/ ON or OFF |
| The value of this item only changes when performing an Active Test. |
| Solenoid (SL2) | Shift Solenoid valve SL2 Status/ ON or OFF |
| The value of this item only changes when performing an Active Test. |
| Solenoid (SL3) | Shift Solenoid valve SL3 Status/ ON or OFF |
| The value of this item only changes when performing an Active Test. |
| Solenoid (SL4) | Shift Solenoid valve SL4 Status/ ON or OFF |
| The value of this item only changes when performing an Active Test. |
| Solenoid (SL) | Shift Solenoid SL Status/ ON or OFF |
| The value of this item only changes when performing an Active Test. |
Enter the following menus: Powertrain / Engine / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Throttle Sensor Position | Throttle sensor position/ Min.: 0%, Max.: 100% |
|
|
| Sport Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sport Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| ACTIVE TEST |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the TC Terminal | Connects and disconnects terminals TC and TE1 (changes to the fluid temperature detection mode) | ON/OFF |
|
| Activate the Solenoid (SLU) | Operates the shift solenoid valve SLU | ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (SLT) | Operates the shift solenoid valve SLT to raise the line pressure | ON/OFF
| [Vehicle Condition]
|
| Activate the Lock Up Solenoid | Controls the shift solenoid valves SLU and SL to control the automatic transaxle lock-up condition | ON/OFF | Can be used to check the operation of the shift solenoid valves SLU and SL. [Vehicle Condition]
|
| Activate the Solenoid (SL) | Operates the shift solenoid valve SL | ON/OFF | [Vehicle Condition]
|
| Control the Shift Position | Operates the shift solenoid valves to allow gears to be selected manually |
| Can be used to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition]
|
| Activate the Solenoid (SL1) | Operates the shift solenoid valve SL1 | ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL2) | Operates the shift solenoid valve SL2 | ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL3) | Operates the shift solenoid valve SL3 | ON/OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL4) | Operates the shift solenoid valve SL4 | ON/OFF | [Vehicle Condition]
|