Home › Drivetrain ยท U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

AUTOMATIC TRANSAXLE SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Transmission / Data List.

    HINT:
    1. To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
    2. When you select a measurement group, the ECU data belonging to that group is displayed.
    3. Measurement Group List / Description
      1. Primary / -
      2. All Data / All data
      3. Engine Control / Engine control system related data
      4. Vehicle Information / Vehicle information

  7. Read the Data List according to the display on the GTS.

    HINT:
    1. The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.
    2. "Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.


    Transmission 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 MPH), Max.: 255 km/h (158 MPH)
    Actual vehicle speed
    1. This is the current vehicle speed.
    2. The vehicle speed is detected using the wheel speed sensors.
      1. There is a delay in when the vehicle speed data is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunctio n occurred when the vehicle was stopped.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    600 to 700 rpm: Idling (shift lever in P, engine warmed up and A/C off)
    When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
    Calculate Load
    Load calculated by ECM/
    Min.: 0%, Max.: 100%
    20 to 40%: Idling with warmed up engine
    1. This is the engine load calculated based on the estimated intake pressure.
    2. Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%) (For example, when the actual intake manifold pressure is the same as atmospheric pressure, Calculate Load is 100%.)
    Coolant Temperature
    Engine coolant temperature/
    Min.: -40°C (-40°F), Max.: 140°C (284°F)
    75 to 100°C (167 to 212°F): After warming up
    This is the engine coolant temperature.

    HINT:
    1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
    2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    3. If the value is -40°C (-40°F), or 140°C (284°F) or higher, the sensor circuit is open or shorted.
    4. Check if the engine overheats when the value indicates higher than 140°C (284°F).

    Intake Air Temperature
    Intake air temperature/
    Min.: -40°C (-40°F)
    Max.: 140°C (284°F)
    Equivalent to temperature at location of mass air flow meter sub-assembly
    This is the intake air temperature.

    HINT:
    1. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
    2. If the value is -40°C (-40°F), or 140°C (284°F), the sensor circuit is open or shorted.

    Engine Run Time
    Engine run time/
    Min.: 0 sec., Max.: 65535 sec.
    Time after engine start
    This is the time elapsed since the engine was started.

    HINT:
    The time is counted only while the engine is running.

    Battery Voltage
    Battery voltage/
    Min.: 0, Max.: 65.5 V
    11 to 14 V: Idling
    If 11 V or less, the characteristics of some electrical components may change.
    BATT Voltage
    Battery voltage/
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Idling
    If 11 V or less, the characteristics of some electrical components may change.
    Throttle Position Sensor No.1 Voltage %
    Absolute throttle position sensor No. 1/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Accelerator pedal fully released
    2. 64 to 96%: Accelerator pedal fully depressed
    The No. 1 throttle position sensor output is converted using 5 V = 100%.

    HINT:
    If there are no throttle position sensor DTCs stored, it is possible to conclude that the throttle position sensor system is normal.

    Starter SW
    Starter signal/
    OFF or ON
    1. ON: Starter operating
    2. OFF: Starter not operating
    -
    Neutral Position SW
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    Stop Light SW
    Stop light switch status/
    ON or OFF
    1. ON: Brake pedal depressed
    2. OFF: Brake pedal released
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    Avail: The monitor is available on the vehicle.
    Not Avl: The monitor is not available on the vehicle.
    TC terminal
    TC terminal Status/
    ON or OFF
    OFF
    -
    MIL
    MIL status/
    ON or OFF
    OFF
    -
    MIL ON Run Distance
    Distance driven with MIL on/
    Min.: 0 km (0 mile),
    Max.: 65535 km (40723 mile)
    -
    This is the distance driven since the MIL was illuminated
    Running Time from MIL ON
    Running time from MIL on/
    Min.: 0 minute,
    Max.: 65535 minutes
    Running time since the MIL illuminated
    -
    Time after DTC Cleared
    Time after DTCs cleared/
    Min.: 0 min,
    Max.: 65535 minutes
    Time elapsed since DTCs cleared
    This is the time elapsed since the DTCs were cleared (or the vehicle left the factory). Time elapsed after the engine switch is turned off is not counted.
    Distance from DTC Cleared
    Distance driven after DTCs cleared/
    Min.: 0 km (0 mile),
    Max.: 65535 km (40723 mile)
    Distance driven since DTCs cleared
    This is the distance driven since the DTCs were cleared (or after the vehicle left the factory).
    Warmup Cycle Cleared DTC
    Warm-up cycles after DTCs cleared/
    Min.: 0, Max.: 255
    -
    1. This is the number of warmup cycles since the DTCs were cleared.
    2. This is the number of times the engine was warmed up* since the DTCs were cleared (or after the vehicle left the factory).
      *: An engine warmup is defined as the engine coolant temperature rising 20°C (36°F) or higher and reaching a temperature of 70°C (158°F) or higher after the engine is started.
    OBD Requirements
    OBD requirement/
    -
    EOBD (Euro-OBD)
    -
    Number of Emission DTC
    Emissions-related DTCs/
    Min.: 0,
    Max.: 127
    -
    This is the number of emissions-related DTCs.
    Total Distance Traveled
    Total distance traveled/
    Min.: 0 km (0 mile),
    Max.: 16777215 km (10425361 mile)
    -
    -
    Total Distance Traveled
    Total distance traveled/
    Min.: 0 km (0 mile),
    Max.: 27000309 km (16777992 mile)
    -
    -
    NT Sensor Speed
    Input turbine speed/
    Min.: 0 rpm, Max.: 12750 rpm
    1. Equal to engine speed: Lock-up on (after warming up the engine)
    2. Nearly equal to engine speed: Lock-up off (idling with shift lever in N)
    Data is displayed in increments of 50 rpm
    NC Sensor Speed
    Counter gear speed/
    Min.: 0 rpm, Max.: 12750 rpm
    -
    Data is displayed in increments of 50 rpm.
    Shift SW Status (P Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in P
    2. OFF: Shift lever not in P
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    Shift SW Status (R Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in R
    2. OFF: Shift lever not in R
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    Shift SW Status (N Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in N
    2. OFF: Shift lever not in N
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    Shift SW Status (N,P Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in P or N
    2. OFF: Shift lever not in P or N
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    Shift SW Status (S Range)
    S mode select switch status/
    ON or OFF
    1. ON: Shift lever in S, "+" or "-"
    2. OFF: Shift lever not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    Park/neutral position switch status/
    ON or OFF
    1. ON: Shift lever in D or S
    2. OFF: Shift lever not in D or S
    When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

    HINT:
    If the same malfunction occurs even after adjusting these parts, Click here.

    A/T Oil Temperature No.1
    ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 150°C (302°F)
    1. Approximately 80°C (176°F): After stall speed test
    2. Equal to ambient temperature after cold soak
    If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted.
    NT Sensor Voltage
    Input speed sensor NT output voltage/
    Min.: 0.000 V, Max.: 4.999 V
    0.1 to 1.9 V
    -
    NC Sensor Voltage
    Output speed sensor NC output voltage/
    Min.: 0.000 V, Max.: 4.999 V
    0.1 to 1.9 V
    -
    Lock Up Status
    Lock up/
    ON or OFF
    1. ON: Lock-up operating
    2. OFF: Lock-up not operating
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Same as actual gear
    -
    Solenoid (SLT)
    Shift solenoid valve SLT status/
    ON or OFF
    1. ON: Shift solenoid valve SLT operating
    2. OFF: Shift solenoid valve SLT not operating
    -
    Solenoid (SLU)
    Shift Solenoid valve SLU Status/
    ON or OFF
    1. ON: Shift solenoid valve SLU operating
    2. OFF: Shift solenoid valve SLU not operating
    -
    Solenoid (SL1)
    Shift Solenoid valve SL1 Status/
    ON or OFF
    1. ON: Shift solenoid valve SL1 operating
    2. OFF: Shift solenoid valve SL1 not operating
    The value of this item only changes when performing an Active Test.
    Solenoid (SL2)
    Shift Solenoid valve SL2 Status/
    ON or OFF
    1. ON: Shift solenoid valve SL2 operating
    2. OFF: Shift solenoid valve SL2 not operating
    The value of this item only changes when performing an Active Test.
    Solenoid (SL3)
    Shift Solenoid valve SL3 Status/
    ON or OFF
    1. ON: Shift solenoid valve SL3 operating
    2. OFF: Shift solenoid valve SL3 not operating
    The value of this item only changes when performing an Active Test.
    Solenoid (SL4)
    Shift Solenoid valve SL4 Status/
    ON or OFF
    1. ON: Shift solenoid valve SL4 operating
    2. OFF: Shift solenoid valve SL4 not operating
    The value of this item only changes when performing an Active Test.
    Solenoid (SL)
    Shift Solenoid SL Status/
    ON or OFF
    1. ON: Shift solenoid valve SL operating
    2. OFF: Shift solenoid valve SL not operating
    The value of this item only changes when performing an Active Test.

  8. Enter the following menus: Powertrain / Engine / Data List.

  9. Read the Data List according to the display on the GTS.

    Engine 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Throttle Sensor Position
    Throttle sensor position/
    Min.: 0%,
    Max.: 100%
    1. 0%: Accelerator pedal fully released
    2. 50 to 80%: Accelerator pedal fully depressed (engine running)
    1. This is the throttle valve opening amount used for engine control.
    2. This value has no meaning when the engine switch is on (IG) and the engine is stopped.
    3. The throttle valve opening amount during idling is indicated by 0%.
    Sport Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Continuously shift to "+" (Up shift)
    2. OFF: Release "+" (Up shift)
    -
    Sport Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Continuously shift to "-" (Down shift)
    2. OFF: Release "-" (Down shift)
    -


ACTIVE TEST

HINT:
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the engine switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the engine switch on (IG).

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / Transmission / Active Test.

  7. Perform the Active Test according to the display on the GTS.

    Transmission 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the TC Terminal
    Connects and disconnects terminals TC and TE1
    (changes to the fluid temperature detection mode)
    ON/OFF
    1. Confirm that the vehicle is stopped.
    2. ON: TC and TE1 (CG) are connected.
    3. OFF: TC and TE1 (CG) are disconnected.
    4. The MIL will not blink when "Activate the TC Terminal / ON" is selected.
    Activate the Solenoid (SLU)
    Operates the shift solenoid valve SLU
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N
    Activate the Solenoid (SLT)
    Operates the shift solenoid valve SLT to raise the line pressure
    ON/OFF

    HINT:
    1. ON: No action (normal operation)
    2. OFF: Line pressure increases
      (When Active Test "Activate the Solenoid (SLT)" is performed, the ECM commands the shift solenoid valve SLT to turn off)

    [Vehicle Condition]
    1. Vehicle Stopped
    2. IDL: ON
    Activate the Lock Up Solenoid
    Controls the shift solenoid valves SLU and SL to control the automatic transaxle lock-up condition
    ON/OFF
    Can be used to check the operation of the shift solenoid valves SLU and SL.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 20%
    2. Vehicle speed: 60 km/h (37 mph) or more in 6th gear
    Activate the Solenoid (SL)
    Operates the shift solenoid valve SL
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N
    Control the Shift Position
    Operates the shift solenoid valves to allow gears to be selected manually
    1. Press "→" button: Upshift occurs
    2. Press "←" button: Downshift occurs
    Can be used to check the operation of the shift solenoid valves.
    Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes.
    Do not downshift at high speeds. Doing so will damage the automatic transaxle.
    [Vehicle Condition]
    1. 50 km/h (31 mph) or less
    Activate the Solenoid (SL1)
    Operates the shift solenoid valve SL1
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N
    Activate the Solenoid (SL2)
    Operates the shift solenoid valve SL2
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N
    Activate the Solenoid (SL3)
    Operates the shift solenoid valve SL3
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N
    Activate the Solenoid (SL4)
    Operates the shift solenoid valve SL4
    ON/OFF
    [Vehicle Condition]
    1. Engine not running
    2. Shift lever in P or N

    HINT:
    1. The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. Line pressure changes are confirmed using the same SST that is used for the Hydraulic Test (Click here).
    2. Note that the pressure readings for the Active Test and Hydraulic Test are different.