Home › Drivetrain · U761E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P275613    Torque Converter Clutch Pressure Control Solenoid Control Circuit Open

for Preparation Click here


DESCRIPTION

The ECM uses signals from the throttle position sensor, air-flow meter, input speed sensor NT, output speed sensor NC and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C315080E01


Text in Illustration 
*a
Spool Valve
*b
Sleeve
*c
Solenoid Coil
*d
Hydraulic Pressure
*e
Current
-
-
The ECM compares the engagement condition of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical malfunctions of the shift solenoid valve SLU, transmission valve body assembly and torque converter clutch.

DTC No.
DTC Detection Condition
Trouble Area
P275613
1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
  1. The vehicle is being driven.
  2. An open or short in the shift solenoid valve SLU circuit is detected.
  3. 1 second
  4. 1-trip detection logic
  1. Wiring Harness Connector
  2. Open or short in shift solenoid valve SLU circuit
  3. Shift solenoid valve SLU
  4. ECM

MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLU circuit is detected, the ECM determines there is a malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM


C314405E05


INSPECTION PROCEDURE

NOTICE:
Perform registration and/or initialization when parts related to the automatic transaxle are replaced (Click here).

HINT:
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
  1. Perform the Lock-up Function inspection in Road Test (Click here).
  2. Check for DTCs again (Click here).

1.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SLU CIRCUIT)
  1. Disconnect the E96 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-3 (SLU+) - E96-2 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    E96-3 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E96-2 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
Go to step 2
OK

REPLACE ECM (Click here)  

2.CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)
  1. Disconnect the E8 connector from the wiring harness connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E96-3 (SLU+) - E8-14 (SLU+)
    Always
    Below 1 Ω
    E96-2 (SLU-) - E8-5 (SLU-)
    Always
    Below 1 Ω
    E96-3 (SLU+) or E8-14 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    E96-2 (SLU-) or E8-5 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT TRANSMISSION WIRE (SLU)


    C315790E08
  1. Remove the wiring harness connector.
    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-11 (SLU+) - A-5 (SLU-)
    20°C (68°F)
    5.0 to 5.6 Ω
    A-11 (SLU+) - Body ground and other terminals
    Always
    10 kΩ or higher
    A-5 (SLU-) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
Go to step 4
OK

REPLACE WIRING HARNESS CONNECTOR (Click here)  

4.INSPECT SHIFT SOLENOID VALVE SLU


    C201747E01
  1. Remove the shift solenoid valve SLU.
    Text in Illustration 
    *1
    Shift Solenoid Valve SLU

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

    OK:
    Valve moves and makes an operating sound.



NG
REPLACE SHIFT SOLENOID VALVE SLU (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)