DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|
| P0430 | The oxygen storage capacity value is less than the standard value under active air fuel ratio control (2 trip detection logic). |
|

| *1 | Air Fuel Ratio Sensor (Bank 1 Sensor 1) | *2 | Air Fuel Ratio Sensor (Bank 2 Sensor 1) |
| *3 | Heated Oxygen Sensor (Bank 1 Sensor 2) | *4 | Heated Oxygen Sensor (Bank 2 Sensor 2) |
| *5 | TWC: Front Catalyst | *6 | TWC: Rear Catalyst |
| *7 | Center Exhaust Pipe Assembly | *8 | Tail Exhaust Pipe Assembly RH |
| *9 | Tail Exhaust Pipe Assembly LH | *10 | Exhaust Manifold Sub-assembly RH |
| *11 | Exhaust Manifold Sub-assembly LH | *12 | Front Exhaust Pipe Assembly |
| Required Sensors/Components (Main) | Air fuel ratio sensor Heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor Mass air flow meter sub-assembly Crankshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Idling | Off |
| Engine speed | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10% or higher, and less than 70% |
| All of the following conditions are met | 1, 2 and 3 |
| 1. Mass air flow | 5 gm/sec or more, and less than 75 gm/sec |
| 2. Front catalyst temperature (estimated) | 520°C (968°F) or higher, and less than 800°C (1472°F) |
| 3. Rear catalyst temperature (estimated) | 300°C (572°F) or higher, and less than 800°C (1472°F) |
| Shift position | 3rd or higher |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|


| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 and/or P0430 are output | A |
| DTC P0420 and/or P0430 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Turn the tester on.
Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.
Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 AFS Voltage B2S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| -12% | Lean | Higher than 3.4 V | |
| O2S B1S2 O2S B2S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| -12% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 or AFS Voltage B2S1 | Status O2S B1S2 or O2S B2S2 | Actual air fuel ratio, air fuel ratio sensor and heated oxygen sensor condition | Misfire | Main Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | - |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | - |
| |
| Lean/Rich | Lean | Heated oxygen sensor malfunction | - |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction | - |
| |
| Lean | Lean | Actual air fuel ratio lean | May occur |
| D |
| Rich | Rich | Actual air fuel ratio rich | - |
|
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A, C |
| DTC P0430 is output | B, C |
| DTC P0420 and P0430 are output | A, B, C |
|
| ||||
|
| ||||
| C | ||
| ||
| 5.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
|
| ||||
| 7.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
|
| ||||
| 8.REPAIR OR REPLACE EXHAUST GAS LEAK POINT |
Repair or replace exhaust gas leak point.
|
| ||||
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
|
| ||||
| 10.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .
| NEXT | |
| 11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine.
Turn the tester on.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 and/or P0430 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0420 is output | A, C |
| DTC P0430 is output | B, C |
| DTC P0420 and P0430 are output | A, B, C |
|
| ||||
|
| ||||
| C | ||
| ||