Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > Check CAN Bus Lines for Short Circuit (LHD Models)

for Preparation Click here


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
  1. Short in CAN main bus lines
  2. Short in CAN branch lines
  3. AFS ECU*1
  4. ECM
  5. Main body ECU (Multiplex network body ECU)
  6. Combination meter assembly
  7. Brake actuator assembly
  8. Steering sensor
  9. Clearance warning ECU assembly*2
  10. Power steering ECU with motor assembly
  11. Airbag sensor assembly
  12. Air conditioning amplifier assembly
  13. Smart key ECU assembly (Certification ECU)*3
  14. Navigation receiver assembly*4
  15. Radio and display receiver assembly*5
  16. Network gateway ECU*6
  17. Inner rear view mirror assembly*7
  18. Telematics transceiver*8
  19. CAN No. 1 junction connector
  20. CAN No. 2 junction connector
*1: w/ AFS
*2: w/ Toyota Parking Assist-sensor System
*3: w/ Smart Entry and Start System
*4: for Navigation Receiver Type
*5: for Radio and Display Type
*6: w/ Network Gateway ECU
*7: w/ Automatic High Beam System
*8: w/ Telematics Transceiver

WIRING DIAGRAM


C244448E06


C370610E01


C311103E02


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON, wait at least 31 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes. Check that the warning light remains off after turning off following the initial light check.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
  3. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.

1.CHECK VEHICLE TYPE
  1. Check vehicle type.

    Result:
    Result
    Proceed to
    except TMMR Made
    A
    for TMMR Made
    B



B
Go to step 11
A


2.CHECK FOR SHORT IN CAN BUS LINES (DLC3 BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C241463E06
  1. Disconnect the DLC3 branch line connector (I96) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to DLC3

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
OK


3.CHECK FOR SHORT IN CAN BUS LINES (BRANCH LINE)
  1. Reconnect the DLC3 branch line connector (I96) to the CAN No. 1 junction connector.



    C292403E01
  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
    Text in Illustration 
    *1
    DLC3



  1. While observing the resistance value shown on the tester, disconnect connectors (I95, I97, I100, I102, I103, I105, I106, I107, I111, I112 and I188) from the CAN No. 1 junction connector or CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).

    HINT:
    Disconnect the branch line connectors other than those of the DLC3.


    C311104E02


    Text in Illustration 
    *A
    w/ Toyota Parking Assist-sensor System
    *B
    w/ Smart Entry and Start System
    *C
    for Navigation Receiver Type
    *D
    for Radio and Display Type
    *E
    w/ Network Gateway ECU
    *F
    w/ AFS
    *1
    Clearance Warning ECU Assembly
    *2
    Air Conditioning Amplifier Assembly
    *3
    ECM
    *4
    Brake Actuator Assembly
    *5
    Smart Key ECU Assembly (Certification ECU)
    *6
    Navigation Receiver Assembly
    *7
    Radio and Display Receiver Assembly
    *8
    Network Gateway ECU
    *9
    Combination Meter Assembly
    *10
    Power Steering ECU with Motor Assembly
    *11
    DLC3
    *12
    Airbag Sensor Assembly
    *13
    Steering Sensor
    *14
    Main Body ECU (Multiplex Network Body ECU)
    *15
    AFS ECU
    *16
    CAN No. 1 Junction Connector
    *17
    CAN No. 2 Junction Connector
    -
    -

    C241464E20


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 1 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 1 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    AFS ECU*
    I112
    BE
    W
    Main body ECU (Multiplex network body ECU)
    I95
    P
    W
    Steering sensor
    I97
    V
    W
    Airbag sensor assembly
    I103
    Y
    W
    DLC3
    I96
    L
    W
    Power steering ECU with motor assembly
    I100
    G
    W
    Combination meter assembly
    I94
    R
    W
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I93
    B
    W
    *: w/ AFS

    C311106E01


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 2 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 2 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I101
    B
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    ECM
    I104
    P
    W
    Smart key ECU assembly (Certification ECU)*1
    I106
    L
    W
    Clearance warning ECU assembly*2
    I111
    BE
    W
    Network Gateway ECU*3
    I188
    G
    W
    1. Navigation receiver assembly*4
    2. Radio and display receiver assembly*5
    I107
    R
    W
    Brake actuator assembly
    I105
    Y
    W
    *1: w/ Smart Entry and Start System
    *2: w/ Toyota Parking Assist-sensor System
    *3: w/ Network Gateway ECU
    *4: for Navigation Receiver Type
    *5: for Radio and Display Type

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.


    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of the branch lines.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.)
    B

  1. When there is a short in one or more of the branch lines:

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



B
Go to step 8
A


4.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)


    C241466E06
  1. Disconnect the combination meter assembly main bus line connector (I94) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to Combination Meter Assembly

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when the combination meter assembly connector is disconnected. (There are no shorts in the combination meter assembly or between its main bus lines.)
    A
    The resistance falls within the specified range (between 108 and 132 Ω) (the other terminating resistor is normal) when the combination meter assembly connector is disconnected. (There is a short in the combination meter assembly or between its main bus lines.)
    B



B
Go to step 9
A


5.CHECK FOR SHORT IN CAN BUS LINE (ECM MAIN LINE)


    C311105E01
  1. Disconnect the ECM main bus line connector (I104) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to ECM

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    HINT:
    Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.


    Result:

    Symptom
    Proceed to
    The resistance is still below 1 MΩ when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.)
    A
    The resistance becomes 1 MΩ or higher when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.)
    B



B
Go to step 10
A


6.CHECK CAN NO. 1 JUNCTION CONNECTOR


    C240089E10
  1. Disconnect the CAN main bus line connector (I93) from the CAN No. 1 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to CAN No. 2 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3



NG
REPLACE CAN NO. 1 JUNCTION CONNECTOR
OK


7.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)
  1. Reconnect the CAN main bus line connector (I93) to the CAN No. 1 junction connector.



    C250962E02
  1. Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to CAN No. 1 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

Text in Illustration 
*1
DLC3


NG
REPAIR OR REPLACE CAN BUS MAIN LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

8.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
  1. Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the short-circuited branch line is connected (Click here).



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

9.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
  1. Reconnect the combination meter assembly main bus line connector (I94) to the CAN No. 1 junction connector.

  1. Disconnect the I18 combination meter assembly connector.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.



NG
REPAIR OR REPLACE CAN BUS MAIN LINES (COMBINATION METER ASSEMBLY MAIN LINES)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

10.CHECK FOR SHORT IN CAN BUS LINES (ECM)
  1. Reconnect the ECM main bus line connector (I104) to the CAN No. 2 junction connector.

  1. Disconnect the A25 ECM connector.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher

    Text in Illustration 
    *1
    DLC3

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AR-FE)
    B
    NG
    C

    HINT:
    1. Measure the resistance with the combination meter assembly main bus line connector (I94) disconnected.
    2. If the resistance changes to 1 MΩ or higher when the connector is disconnected, there may be a short in the ECM.



B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN LINES)
A

REPLACE ECM (Click here)  

11.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 1 JUNCTION CONNECTOR)


  1. Disconnect the I198 CAN No. 1 junction connector.


    C283770E05


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to CAN No. 1 Junction Connector)
    *b
    to AFS ECU*1
    (for V Bus)
    *c
    to Combination Meter Assembly
    (for V Bus)
    *d
    to Main Body ECU (Multiplex Network Body ECU)
    (for V Bus)
    *e
    to DLC3
    (for V Bus)
    *f
    to Steering Sensor
    (for V Bus)
    *g
    to Airbag Sensor Assembly
    (for V Bus)
    *h
    to Power Steering ECU with Motor Assembly
    (for V Bus)
    *i
    to Inner Rear View Mirror Assembly*2
    (for V Bus)
    *j
    to Telematics Transceiver*3
    (for V Bus)
    *k
    to CAN No. 2 Junction Connector
    (for V Bus)
    -
    -
    *1: w/ AFS
    *2: w/ Automatic High Beam System
    *3: w/ Telematics Transceiver

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    Connected to
    I198-1 (CANH) - I198-11 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    AFS ECU*1
    I198-2 (CANH) - I198-12 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    Combination meter assembly
    I198-3 (CANH) - I198-13 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Main body ECU (Multiplex network body ECU)
    I198-4 (CANH) - I198-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    1 MΩ or higher
    DLC3
    I198-5 (CANH) - I198-15 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Steering sensor
    I198-6 (CANH) - I198-16 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Airbag sensor assembly
    I198-7 (CANH) - I198-17 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Power steering ECU with motor assembly
    I198-8 (CANH) - I198-18 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Inner rear view mirror assembly*2
    I198-9 (CANH) - I198-19 (CANL)
    Cable disconnected from negative (-) battery terminal
    200 Ω or higher
    Telematics transceiver*3
    I198-10 (CANH) - I198-20 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω
    CAN No. 2 junction connector

    *1: w/ AFS
    *2: w/ Automatic High Beam System
    *3: w/ Telematics Transceiver

    Result:

    Result
    Proceed to
    OK
    A
    NG (CAN No. 2 junction connector main lines)
    B
    NG (Combination meter assembly main lines)
    C
    NG (DLC3 branch line)
    D
    NG (ECU or sensor branch line)
    E



B
Go to step 12

C
Go to step 15

D
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

E
Go to step 16
A

REPLACE CAN NO. 1 JUNCTION CONNECTOR 

12.CHECK CAN NO. 2 JUNCTION CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)
  1. Reconnect the I198 CAN No. 1 junction connector.



    C250962E02
  1. Disconnect the CAN main bus line connector (I101) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to CAN No. 1 Junction Connector

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

Text in Illustration 
*1
DLC3


NG
REPAIR OR REPLACE CAN BUS MAIN LINES (CAN NO. 1 JUNCTION CONNECTOR - CAN NO. 2 JUNCTION CONNECTOR)
OK


13.CHECK FOR SHORT IN CAN BUS LINES (CAN NO. 2 JUNCTION CONNECTOR)
  1. Reconnect the CAN main bus line connector (I101) to CAN No. 2 junction connector.



    C292403E01
  1. Connect the probes of an ohmmeter to terminals 6 (CANH) and 14 (CANL) of the DLC3.
    Text in Illustration 
    *1
    DLC3



  1. While observing the resistance value shown on the tester, disconnect connectors (I102, I105, I106, I107, I111 and I188) from the CAN No. 2 junction connector one by one until the resistance becomes normal (between 54 and 69 Ω).


    C311106E02


    Text in Illustration 
    *a
    Component without harness connected
    (CAN No. 2 Junction Connector)
    -
    -

    Wiring Color 
    CAN No. 2 Junction Connector Side
    Code
    Color (CANH Side)
    Color (CANL Side)
    CAN main bus line (bus line connecting CAN No. 1 junction connector and CAN No. 2 junction connector)
    I101
    B
    W
    Air conditioning amplifier assembly
    I102
    V
    W
    ECM
    I104
    P
    W
    Smart key ECU assembly (Certification ECU)*1
    I106
    L
    W
    Clearance warning ECU assembly*2
    I111
    BE
    W
    1. Navigation receiver assembly*3
    2. Radio and display receiver assembly*4
    I107
    R
    W
    Network Gateway ECU*5
    I188
    G
    W
    Brake actuator assembly
    I105
    Y
    W
    *1: w/ Smart Entry and Start System
    *2: w/ Toyota Parking Assist-sensor System
    *3: for Navigation Receiver Type
    *4: for Radio and Display Type
    *5: w/ Network Gateway ECU

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.


    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when all the specified connectors are disconnected. (There are no shorts between a pair of the branch lines.)
    A
    The resistance becomes normal (between 54 and 69 Ω) when a connector is disconnected. (There is a short between one or more pairs of branch lines.)
    B

  1. When there is a short in one or more of the branch lines:

    1. Reconnect all of the connectors to the CAN junction connector, except for the one that was disconnected last (the short-circuited bus line). Check that the resistance shown on the tester is normal (between 54 and 69 Ω) to confirm that there is a short in the one branch line only.

      HINT:
      1. Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
      2. Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



B
Go to step 16
A


14.CHECK FOR SHORT IN CAN BUS LINES (ECM MAIN LINE)


    C311105E01
  1. Disconnect the ECM main bus line connector (I104) from the CAN No. 2 junction connector.
    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to CAN No. 2 Junction Connector)
    *b
    to ECM

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    Result:

    Symptom
    Proceed to
    The resistance is still below 54 Ω when the ECM connector is disconnected. (There are no shorts in the ECM or between its main bus lines.)
    A
    The resistance becomes normal (between 108 to 132 Ω) when the ECM connector is disconnected. (There is a short in the ECM or between its main bus lines.)
    B



B
Go to step 17
A

REPLACE CAN NO. 2 JUNCTION CONNECTOR 

15.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY MAIN LINE)
  1. Reconnect the I198 CAN No. 1 junction connector.

  1. Disconnect the I18 combination meter assembly connector.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.



NG
REPAIR OR REPLACE CAN BUS MAIN LINES (COMBINATION METER ASSEMBLY MAIN LINES)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

16.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
  1. Reconnect the connector for the short-circuited branch line to the CAN junction connector (the connector that caused the bus line resistance to become normal (between 54 and 69 Ω) when it was disconnected).

  1. Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU or sensor to which the short-circuited branch line is connected (Click here).



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *1
    DLC3

    HINT:
    If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

17.CHECK FOR SHORT IN CAN BUS LINES (ECM)
  1. Reconnect the ECM main bus line connector (I104) to the CAN No. 2 junction connector.

  1. Disconnect the A25 or A84 ECM connector.



    C292403E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I39-6 (CANH) - I39-14 (CANL)
    Cable disconnected from negative (-) battery terminal
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3

    Result:
    Result
    Proceed to
    OK (for 2GR-FE)
    A
    OK (for 2AR-FE)
    B
    OK (for 6AR-FSE)
    C
    NG
    D

    HINT:
    If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the ECM.



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN BUS MAIN LINES (ECM MAIN LINES)
A

REPLACE ECM (Click here)