Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows)

POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) > Rear Power Window LH does not Operate with Rear Power Window Switch LH

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the power window regulator motor assembly (for rear LH door) is operated by the rear power window regulator switch assembly (for LH door). The power window regulator motor assembly (for rear LH door) has motor, regulator, and ECU functions.

WIRING DIAGRAM


B203373E94


INSPECTION PROCEDURE

NOTICE:
  1. The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the power window control system after confirming that the communication system is functioning properly.
  2. If the power window regulator motor assembly (for rear LH door) has been replaced with a new one, initialize the power window control system (Click here).

1.READ VALUE USING INTELLIGENT TESTER (MAIN BODY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Communication RL-Door Motor
    Connection status between power window regulator motor assembly (for rear LH) and main body ECU (multiplex network body ECU) / OK or STOP
    OK: Normal communication
    STOP: Communication stopped
    -

    OK:
    On the intelligent tester screen, OK is displayed.



NG
GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (RL-DOOR MOTOR)
  1. Enter the following menus: Body / RL-Door Motor / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Up SW
    Rear LH door power window manual up switch signal / ON or OFF
    ON: Rear LH door power window manual up switch operated
    OFF: Rear LH door power window manual up switch not operated
    -
    RL Door P/W Down SW
    Rear LH door power window manual down switch signal / ON or OFF
    ON: Rear LH door power window manual down switch operated
    OFF: Rear LH door power window manual down switch not operated
    -

    OK:
    On the intelligent tester screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RL-DOOR MOTOR)
  1. Enter the following menus: Body / RL-Door Motor / Active Test.

  1. Perform the Active Test according to the display on the intelligent tester.

    CAUTION:
    Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


    RL-Door Motor (Power Window Regulator Motor Assembly (for Rear LH Door)) 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Power Window
    Power window
    OFF / UP / DOWN
    -

    OK:
    Rear LH power window operates normally.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR)


    B203473E30
  1. Remove the rear power window regulator switch assembly (for LH door) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Auto up or up position
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Auto down or down position
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Rear Power Window Regulator Switch Assembly (for LH Door))



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (FOR LH DOOR) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (REAR WINDOW REGULATOR SWITCH (FOR LH DOOR) - REGULATOR MOTOR (FOR REAR LH DOOR) AND BODY GROUND)
  1. Disconnect the power window regulator motor assembly (for rear LH door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    M4-6 (UP) - M2-10 (UP)
    Always
    Below 1 Ω
    M4-7 (DOWN) - M2-7 (DOWN)
    Always
    Below 1 Ω
    M4-1 (GND) - Body ground
    Always
    Below 1 Ω
    M4-6 (UP) - Body ground
    Always
    10 kΩ or higher
    M4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    M2-10 (UP) - Body ground
    Always
    10 kΩ or higher
    M2-7 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR) (Click here)