Home › Vehicle Exterior › WINDOW / GLASS › REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made)

REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made) > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The following procedure is for the LH side.



1. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.



    B280419
  1. Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    When replacing a rear power window regulator motor assembly, a new rear power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.



3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
  1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

  1. Temporarily install the temporary bolt to the rear door window regulator assembly.



    B280418E04
  1. Temporarily install the rear door window regulator assembly with the 3 bolts.
    Text in Illustration 
    *a
    Temporary Bolt

  1. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

    HINT:
    Tighten the bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    B380668
  1. Slide the rear door glass sub-assembly to install it as shown in the illustration.

    NOTICE:
    Do not damage the rear door glass sub-assembly.



5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    B280411
  1. Install the rear door quarter window glass as shown in the illustration.



6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    B380666
  1. Install the rear door lower window frame sub-assembly with the screw and 2 bolts.



7. INSTALL REAR DOOR GLASS RUN


    B380665
  1. Install the rear door glass run.



8. CONNECT REAR DOOR WEATHERSTRIP


    B405620
  1. Connect the upper part of rear door weatherstrip as shown in the illustration.



9. INSTALL REAR DOOR SERVICE HOLE COVER
  1. Apply new butyl tape to the rear door panel.



    B380669E01
  1. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.
    Text in Illustration 
    *a
    Reference Point

  1. Install the rear door service hole cover according to the reference points on the rear door panel.

    NOTICE:
    Securely install the rear door service hole cover preventing wrinkles and air bubbles.

  1. Connect the connector.



10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    B380670
  1. Install the rear door inner glass weatherstrip.



11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    B380671
  1. Install the No. 1 door scuff plate clamp as shown in the illustration.



    B380662E01
  1. Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
    Text in Illustration 
    *1
    Rear Door Inside Locking Cable Assembly
    *2
    Rear Door Lock Remote Control Cable Assembly



    B380663E01
  1. Engage the 4 claws and reference boss as shown in the illustration.
    Text in Illustration 
    *a
    Reference Boss



    B380659
  1. Engage the 8 clips to install the rear door trim board sub-assembly.

  1. Install the 3 screws.



12. INSTALL REAR ARMREST ASSEMBLY


    B280392
  1. Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.



13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
  1. Connect the connector.



    B380657
  1. Engage the 3 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.



14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    B280388
  1. Engage the 3 claws to install the rear door inside handle bezel plug.



15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



16. INSPECT POWER WINDOW OPERATION
(Click here)