Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Navigation Receiver Type)

NAVIGATION SYSTEM (for Navigation Receiver Type) > Radio Broadcast cannot be Received or Poor Reception

for Preparation Click here


INSPECTION PROCEDURE

1.CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop.
      A
      Automatic station search function stops on a station. (for TMMK Made)
      B
      Automatic station search function stops on a station. (for TMC Made)
      C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


2.CHECK OPTIONAL COMPONENTS
  1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

    Result:
    Result
    Proceed to
    Optional components are not installed.
    A
    Optional components are installed.
    B

    NOTICE:
    Do not remove optional components without the permission of the customer.



B
REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)
A


3.CHECK NAVIGATION RECEIVER ASSEMBLY


    E245523
  1. Preparation for check

    1. Remove the antenna connector from the navigation receiver assembly.

  1. Check for noise

    1. Turn the ignition switch to ACC with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speakers.

      OK:
      Noise can be heard from the speakers.

Result:
Result
Proceed to
OK
A
NG (for TMMK Made)
B
NG (for TMC Made)
C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


4.CHECK WINDOW GLASS ANTENNA WIRE


    E111994E14
  1. Check for continuity in the window glass antenna wire.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    OK:
    There is continuity in the window glass antenna wire.

    Text in Illustration 
    *a
    Tester Probe
    *b
    Antenna Wire
    *c
    Tin Foil



NG
REPAIR WINDOW GLASS ANTENNA WIRE (Click here)
OK


5.INSPECT NAVIGATION RECEIVER ASSEMBLY
  1. Disconnect the RA navigation receiver assembly connector.



    E188455E19
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    RA-5 (ANT+) - Body ground
    Ignition switch ACC
    Radio switch on and AM or FM selected
    11 to 14 V

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A


6.REPLACE ANTENNA CORD SUB-ASSEMBLY
  1. for TMMK Made:
    Replace the antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).
    for TMC Made:
    Replace the antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 7
OK

END 

7.REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
  1. for TMMK Made:
    Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).
    for TMC Made:
    Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.



NG
Go to step 8
OK

END 

8.REPLACE NO. 1 AMPLIFIER ANTENNA ASSEMBLY
  1. for TMMK Made:
    Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).
    for TMC Made:
    Replace the No. 1 amplifier antenna assembly with a new or known good one and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC Made)
    C



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMMK Made) (Click here)

C
REPLACE NAVIGATION RECEIVER ASSEMBLY (for TMC Made) (Click here)
A

END