Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication system. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on the pulses of the voltage.

HINT:
  1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart (Click here).
  2. If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores the DTCs. Troubleshoot the Vehicle Stability Control System (Click here).


WIRING DIAGRAM


E316099E01


INSPECTION PROCEDURE

NOTICE:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (Click here).

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).

    Result:
    Result
    Proceed to
    CAN communication DTCs are not output.
    A
    CAN communication DTCs are output.
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Combination Meter / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240* km/h
    There is a deviation in the values displayed on the speedometer
    (Control range → Speedometer display)
    1. 40 → 41.7 to 46.2
    2. 80 → 83.4 to 88.4
    3. 120 → 125.1 to 130.6
    4. 160 → 166.2 to 173.2
    5. 200 → 207.7 to 215.7

    1. *: except TMMK Made

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.CHECK VEHICLE STABILITY CONTROL SYSTEM
  1. Check if vehicle stability control system DTCs are output (Click here).

Result:
Result
Proceed to
Vehicle stability control system DTCs are not output.
A
Vehicle stability control system DTCs are output.
B



B
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A


4.READ VALUE USING GTS (VEHICLE SPEED, VEHICLE SPEED METER)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch ON.

  1. Turn the GTS on.

  1. Enter the following menus:

    1. for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.

    2. for Combination Meter: Body Electrical / Combination Meter / Data List.

  1. Read the Data List according to the display on the GTS.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed
    -

    Result:

    Result
    Proceed to
    The data list values of the ECUs match.
    A
    The data list values of the ECUs do not match.
    B

    HINT:
    1. When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
    2. When the Data List values of the ECUs do not match, a signal output error of the brake actuator assembly (skid control ECU) or an internal malfunction of the combination meter assembly is suspected.



B
Go to step 5
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

5.REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new or known good one (Click here).


Result:

Result
Proceed to
The operation of the speedometer returns to normal.
A
The operation of the speedometer does not returns to normal.
B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)
A

END