Home › Power Source / Network ยท NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > DIAGNOSIS SYSTEM

for Preparation Click here



ECUS OR SENSORS WHICH COMMUNICATE THROUGH CAN COMMUNICATION SYSTEM
  1. V Bus

    1. ECM

    2. Brake actuator assembly

    3. Main body ECU (Multiplex network body ECU)

    4. Air conditioning amplifier assembly

    5. Power steering ECU with motor assembly

    6. Smart key ECU assembly (Certification ECU)*1

    7. Steering sensor

    8. Clearance warning ECU assembly*2

    9. AFS ECU*3

    10. Combination meter assembly

    11. Navigation receiver assembly*4

    12. Radio and display receiver assembly*5

    13. Airbag sensor assembly

    14. Inner rear view mirror assembly*6

    15. Network gateway ECU*7

  2. Sub Bus 1

    1. Main body ECU (Multiplex network body ECU)

    2. Multiplex tilt and telescopic ECU*8

    3. Position control ECU and switch assembly (for Driver side)*9

    4. Outer mirror control ECU assembly (for Driver side)*9

    5. Outer mirror control ECU assembly (for Front passenger side)*9

  3. Sub Bus 2

    1. Network gateway ECU

    2. Rear television camera assembly*10

    3. Blind spot monitor sensor RH*11

      HINT:
      *1: w/ Smart Entry and Start System
      *2: w/ Toyota Parking Assist-sensor System
      *3: w/ AFS
      *4: for Navigation Receiver Type
      *5: for Radio and Display Type
      *6: w/ Automatic High Beam System
      *7: w/ Network Gateway ECU
      *8: w/ Power Tilt and Power Telescopic Steering Column System
      *9: w/ Seat Position Memory System
      *10: for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)
      *11: w/ Blind Spot Monitor System


CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT ADOPT CAN COMMUNICATION
  1. The systems (ECUs and sensors) that adopt CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

    ECU/Sensor Name
    GTS Display
    Applicability
    ECM
    ECM (Engine)
    Installed on all vehicles
    AFS ECU
    Headlight swivel (AFS)
    Vehicles with AFS
    Combination meter assembly
    Combination Meter
    Installed on all vehicles
    Main body ECU (Multiplex network body ECU)
    Main Body
    Installed on all vehicles
    Power steering ECU with motor assembly
    Power Steering (EPS)
    Installed on all vehicles
    Brake actuator assembly
    Skid Control (ABS/VSC/TRAC)
    Installed on all vehicles
    Steering sensor
    Spiral cable (Steering Angle Sensor)
    Installed on all vehicles
    Airbag sensor assembly
    Airbag
    Installed on all vehicles
    Smart key ECU assembly (Certification ECU)
    Certification (Smart)
    Vehicles with smart entry and start system
    Air conditioning amplifier assembly
    Air Conditioning Amplifier
    Installed on all vehicles
    Navigation receiver assembly
    Display and Navigation (AVN1)
    Vehicles with navigation receiver
    Radio and display receiver assembly
    Display and Navigation (AVN1)
    Vehicles with radio and display
    Clearance warning ECU assembly
    Clearance warning (Clearance Sonar2)
    Vehicles with Toyota parking assist-sensor system
    Multiplex tilt and telescopic ECU
    Multiplex Tilt and Telescopic
    Vehicles with power tilt and power telescopic steering column system
    Network gateway ECU
    CAN Gateway 1
    Vehicles with radio and display (w/ parking assist monitor system without parallel parking assist function)
    Inner rear view mirror assembly
    Front Camera Module
    Vehicles with automatic high beam system
    Rear television camera assembly
    Parking Assist Monitor System 3
    Vehicles with radio and display (w/ parking assist monitor system without parallel parking assist function)
    Outer mirror control ECU assembly (for Driver side)
    Front Door LH/L-Mirror (FL-Door2/L-Miror)
    Vehicles with seat position memory system
    Outer mirror control ECU assembly (for Front passenger side)
    Front Door LH/R-Mirror (FR-Door2/R-Miror)
    Vehicles with seat position memory system
    Position control ECU and switch assembly (for Driver side)
    D-Seat
    Vehicles with seat position memory system
    Blind spot monitor sensor RH
    Blind Spot Monitor Master
    Vehicles with blind spot monitor system

    HINT:
    The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section.


CAN BUS CHECK

HINT:
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.

  1. Using the GTS, select CAN Bus Check screen.

    NOTICE:
    1. It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
    2. In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication (Click here).

    HINT:
    Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.

    Explanation of CAN Bus Check Screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub Bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub Bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check.
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, ''There is no system found on the Communication bus'' will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. If none of the connected ECUs are displayed, or there is no response from the vehicle to the GTS, check the DLC3 branch and the V bus main bus lines for a malfunction.

  2. Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.

    HINT:
    1. If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
    2. If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.


HOW TO INTERPRET CAN BUS CHECK SCREEN
  1. When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.

    NOTICE:
    The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.

    HINT:
    1. When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
    2. Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.



  2. If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
    Example: Open in both CAN branch lines of ECU B on the V bus


    C240692E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of Malfunction
    *e
    Not displayed or background color changes to red or yellow
    *f
    CAN Bus Check Screen

    HINT:
    When there are communication stops, ECUs are present in the vehicle even though they are not displayed on the CAN Bus Check screen.



  3. C240693E01
  4. If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor which is not displayed) is suspected.
    Example: Open in a CAN branch line for ECU D on the V bus
    Text in Illustration 
    *a
    Background color periodically changes to yellow or red
    *b
    Not displayed or background color is yellow or red
    *c
    Not displayed
    Explanation of CAN Bus Check Screen 
    Bus Type
    Background Color
    Connection Status
    V Bus
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub Bus
    (gateway function equipped ECU that does not have history of connected ECUs)*2
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring (unstable communication).
    Not displayed
    Communication stop has continued since the start of the CAN bus check.*1
    Sub Bus
    (gateway function equipped ECU that has history of connected ECUs)*3
    White
    Communication has been normal since the start of the CAN bus check.
    Yellow
    Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication).
    Red
    Currently not communicating (either of the following):
    1. Communication stop has continued since the start of the CAN bus check.
    2. Communication was established at least once since the start of the CAN bus check, but communication is currently not occurring.
    Not displayed
    Either of the following:
    1. If a gateway function equipped ECU cannot communicate, the sub bus and ECUs connected to the sub bus will not be displayed.
    2. If no ECUs are connected to the sub bus, ''There is no system found on the Communication Bus'' will be displayed.

    HINT:
    1. Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    2. *1: ECUs that are present in the vehicle but are not displayed on the CAN Bus Check screen.
    3. *2: Gateway function equipped ECU that does not memorize the sub bus ECUs that are connected to it.
    4. *3: Gateway function equipped ECU that memorizes the sub bus ECUs that are connected to it.
    5. The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of ECU D (output from the other branch line is unstable) and the communication of ECU C is also unstable. In addition, in this example, ECU C is equipped with a gateway function. Therefore, communication is also unstable between the sub bus ECUs of ECU C and the V bus.
    6. The example in the illustration shows that ECU D is not displayed on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of ECU D is suspected.



  5. C240694E01
  6. If a communication error is indicated on both the V bus and sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the V bus first.
    Example: Open in both CAN branch lines of ECU C on the V bus
    Text in Illustration 
    *a
    Not displayed or background color changes to red

    HINT:
    1. In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the V bus after connecting the GTS to the DLC3. As for sub buses, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the V bus.
    2. If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
    3. The CAN Bus Check screen in the illustration shows that ECU C has a gateway function and a communication stop in ECU C is suspected.



  7. C240695E01
  8. If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
    Example: Open in both CAN branch lines of ECU G on the sub bus
    Text in Illustration 
    *a
    Background color changes to red

    HINT:
    1. A communication error in a sub bus does not affect the V bus or other buses.
    2. When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)



  9. If both of the V bus main bus lines are open, ECUs or sensors that are located farther away from the DLC3 than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU A and B are not displayed or their background color changes to red.)


    C240696E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of Malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check Screen

    HINT:
    If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.



  10. If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
    (In this case, ECU I and J are not displayed or their background color changes to red.)


    C240697E01


    Text in Illustration 
    *a
    V Bus
    *b
    Sub Bus
    *c
    Terminating Resistor
    *d
    Location of Malfunction
    *e
    Not displayed or background color is red
    *f
    CAN Bus Check Screen
    *g
    Gateway Function Equipped ECU
    -
    -



  11. C240698E01
  12. When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
    Text in Illustration 
    *a
    When any of the following malfunctions occur on the V bus
    *b
    When any of the following malfunctions occur on a sub bus
    *c
    Not displayed
    Details of Malfunction 
    Short between CAN lines (CANH and CANL)
    Short between a CAN line (CANH or CANL) and +B
    Short between a CAN line (CANH or CANL) and ground
    Open in a CAN main bus line

    HINT:
    1. When a malfunction occurs on the V bus, almost all ECUs and sensors on the V bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the V bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
    2. When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
    3. A communication error in a sub bus does not affect the V bus or other buses.
    4. The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.


HOW TO INTERPRET COMMUNICATION DTCS (DTCS THAT START WITH U)


  1. If a CAN communication error cannot be reproduced, determine the suspected malfunctioning part using the DTCs stored in ECUs that are connected to the CAN buses by following the procedure below.

    HINT:
    Communication DTCs (DTCs that start with U) indicate a communication error between the ECU that stores the DTC and the ECU that is indicated by the DTC.




    1. If multiple ECUs store a communication DTC for a particular ECU, a communication stop of the ECU is suspected.


      C240702E01


      Text in Illustration 
      *a
      Items to be Checked
      -
      -

      NOTICE:
      1. This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.
      2. Even though a DTC title may indicate a communication error with a specific ECU, the ECU name used in the DTC name on the GTS may differ depending on the ECU that stores the DTC. (Regarding output DTCs, refer to step 6 and the DTC chart for each ECU.)

      HINT:
      As multiple ECUs indicate a communication stop with the main body ECU, the possibility of a communication stop of the main body ECU is high.



    2. If almost all of the communication DTCs of an ECU are stored, a communication stop of the ECU is suspected.


      C240703E01


      Text in Illustration 
      *a
      Items to be Checked
      -
      -

      NOTICE:
      This DTC table is from another model, and is only used here to show an example of DTCs that are output when there is an open in a CAN branch line for the main body ECU. This table does not show DTCs applicable to this vehicle.

      HINT:
      1. If almost all of the DTCs of the main body ECU are stored, the possibility of a communication stop of the main body ECU is high.
      2. When a CAN communication error occurs, many DTCs are output. DTCs other than communication error DTCs (such as DTCs that start with C or B) and communication DTCs for the ABS system are important DTCs, however it may be easier to determine the malfunctioning part by examining the overall situation without considering these DTCs.



  2. To help determine the part of the sub bus that has a communication error, prioritize the communication stop DTCs stored in the gateway function equipped ECU.


    C240704E01


    Text in Illustration 
    *a
    Items to be Checked
    *b
    ECM
    *c
    Gateway Function Equipped ECU
    *d
    Location of Malfunction
    *e
    V Bus
    *f
    Sub Bus

    NOTICE:
    This DTC table is from another model, and is only used here to show the ECUs connected to both a V bus and a sub bus. It shows DTCs output when there is an open in the main bus lines for the ECM on the sub bus. This table does not show DTCs applicable to this vehicle.

    HINT:
    1. As gateway function equipped ECUs (sub bus monitor ECU) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
    2. When there is a communication stop for the gateway function equipped ECU (gateway), communication with ECUs connected to other buses such as the V bus stops. Therefore, communication DTCs for ECUs connected to other buses are also stored.

  3. When any of the following malfunctions occurs, many DTCs are likely to be output from many ECUs. Because of this, it may be difficult to determine the probable malfunctioning part.

    1. Short between CAN lines (CANH and CANL)
    2. Short between a CAN line (CANH or CANL) and ground
    3. Short between a CAN line (CANH or CANL) and +B
    4. Open in a CAN branch line (CANH or CANL) of an ECU or sensor
    5. Open in a CAN main bus line (CANH or CANL) between 2 ECUs that have a terminating resistor


DTC TABLE BY ECU

HINT:
  1. In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
  2. If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting (Click here).
  3. If system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.

  1. ECM (for 2AR-FE) / GTS Display "Engine and ECT"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *1: Refer to U760E Automatic Transaxle System (Click here).
    3. *2: Refer to SFI System (Click here).


    ECM (for 2AR-FE) / GTS Display "Engine and ECT" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100*1
    Lost Communication with ECM / PCM "A"
    The TCM does not receive data from the ECM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the ECM is 10.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC remains stored only while malfunction is occurring.
    U0101*2
    Lost Communication with TCM
    The ECM does not receive data from the TCM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the ECM is 10.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC remains stored only while malfunction is occurring.

  2. ECM (for 2GR-FE) / GTS Display "Engine"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: Refer to SFI System (Click here).


    ECM (for 2GR-FE) / GTS Display "Engine" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0101*
    Lost Communication with TCM
    The ECM does not receive data from the TCM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the ECM is 10.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC remains stored only while malfunction is occurring.

  3. TCM (for 2GR-FE) / GTS Display "ECT"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: Refer to U660E Automatic Transaxle System (Click here).


    TCM (for 2GR-FE) / GTS Display "ECT" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100*
    Lost Communication with ECM / PCM "A"
    The TCM does not receive data from the ECM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the TCM is 10.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC remains stored only while malfunction is occurring.

  4. ECM (for 6AR-FSE) / GTS Display "Engine"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: Refer to SFI System (Click here).


    ECM (for 6AR-FSE) / GTS Display "Engine" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U010187*
    Lost Communication with TCM Missing Message
    The ECM does not receive data from the TCM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the ECM is 10 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC is stored until it is cleared using the GTS.

  5. ECM (for 6AR-FSE) / GTS Display "Transmission"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: Refer to U761E Automatic Transaxle System. (Click here).


    ECM (for 6AR-FSE) / GTS Display "Transmission" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U010087*
    Lost Communication with ECM/PCM "A" Missing Message
    The TCM does not receive data from the ECM for 1.25 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the ECM is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    MIL illuminates.
    DTC is stored until it is cleared using the GTS.

  6. Power Steering ECU with Motor Assembly / GTS Display "EMPS"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Power Steering ECU with Motor Assembly / GTS Display "EMPS" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The power steering ECU with motor assembly does not receive data from the ECM for 5 minutes or more.
    All conditions are met:
    1. The ignition switch is ON for 2 seconds or more.
    2. The power source voltage of the power steering ECU with motor assembly is 9 V or more.
    3. Vehicle speed is 20 km/h (12 mph) or more.
    Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 5 minutes.
    EPS warning light illuminates.
    DTC remains stored only while malfunction is occurring.
    U0129
    Lost Communication with Brake System Control Module
    The power steering ECU with motor assembly does not receive data from the brake actuator assembly for 2.34 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the power steering ECU with motor assembly is 9 V or more.
    Turn the ignition switch to ON and wait at least 6 seconds.
    EPS warning light illuminates.
    DTC remains stored only while malfunction is occurring.

  7. Brake Actuator Assembly / GTS Display "ABS/VSC/TRC"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Brake Actuator Assembly / GTS Display "ABS/VSC/TRC" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus OFF
    Bus off is judged for 0.1 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage (+BS terminal voltage) of the brake actuator assembly is between 9.6 and 16.5 V.
    Turn the ignition switch to ON and check that the initial light check illumination turns off, and then wait at least 3 seconds.
    1. ABS warning light illuminates.
    2. Slip indicator light illuminates.
    3. Brake warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM / PCM
    The brake actuator assembly does not receive data from the ECM for 2.5 seconds or more.
    All conditions are met:
    1. Vehicle speed is 6 km/h (4 mph) or more.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage (+BS terminal voltage) of the brake actuator assembly is between 9.6 and 16.5 V.
    Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 6 seconds or more. Check that the warning light remains off after turning off following the initial light check.
    Slip indicator light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0123
    Lost Communication with Yaw Rate Sensor Module
    The brake actuator assembly does not receive data from the airbag sensor assembly for 1.1 seconds or more.
    All conditions are met:
    1. Vehicle speed is 6 km/h (4 mph) or more.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage (+BS terminal voltage) of the brake actuator assembly is between 9.6 and 16.5 V.
    Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check.
    Slip indicator light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0126
    Lost Communication with Steering Angle Sensor Module
    The brake actuator assembly does not receive data from the steering sensor for 1.1 seconds or more.
    All conditions are met:
    1. Vehicle speed is 6 km/h (4 mph) or more.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage (+BS terminal voltage) of the brake actuator assembly is between 9.6 and 16.5 V.
    Turn the ignition switch to ON and drive the vehicle at a speed of 6 km/h (4 mph) or more for 3 seconds or more. Check that the warning light remains off after turning off following the initial light check.
    Slip indicator light illuminates.
    DTC is stored until it is cleared using the GTS.

  8. Steering Sensor / GTS Display "-"

    HINT:
    The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.

  9. Airbag Sensor Assembly / GTS Display "SRS Airbag"

    HINT:
    The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.

  10. Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The main body ECU (multiplex network body ECU) does not receive data from the TCM for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0120
    Lost Communication with Starter / Generator Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0151
    Lost Communication with Restraints Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Instrument Panel Cluster (IPC) Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0164
    Lost Communication with HVAC Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0199
    Lost Communication with ''Door Control Module A''
    The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0200
    Lost Communication with ''Door Control Module B''
    The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0208
    Lost Communication with ''Seat Control Module A''
    The main body ECU (multiplex network body ECU) does not receive data from the position control ECU and switch assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U023A
    Lost Communication with Image Processing Module ''A''
    The main body ECU (multiplex network body ECU) does not receive data from the inner rear view mirror assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0327
    Software Incompatibility with Vehicle Security Control Module
    The main body ECU (multiplex network body ECU) does not receive data from the smart key ECU assembly (certification ECU) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U1002
    Lost Communication with Gateway Module (Main body)
    The main body ECU (multiplex network body ECU) does not receive data from ECUs with a sub bus 1 connection record for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U1115
    Lost Communication with Tilt and Telescopic Module
    The main body ECU (multiplex network body ECU) does not receive data from the multiplex tilt and telescopic ECU for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  11. Smart Key ECU Assembly (Certification ECU) / GTS Display "Entry & Start"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Smart Key ECU Assembly (Certification ECU) / GTS Display "Entry & Start" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM
    The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Main Body ECU
    The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Combination Meter
    The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  12. Smart Key ECU Assembly (Certification ECU) / GTS Display "Power Source Control"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Smart Key ECU Assembly (Certification ECU) / GTS Display "Power Source Control" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM
    The smart key ECU assembly (certification ECU) does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Main Body ECU
    The smart key ECU assembly (certification ECU) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Combination Meter
    The smart key ECU assembly (certification ECU) does not receive data from the combination meter assembly for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the smart key ECU assembly (certification ECU) is 10 V or more.
    Turn the ignition switch to ON and wait at least 20 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  13. Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM
    The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0131
    Lost Communication with Electric Power Steering ECU
    The air conditioning amplifier assembly does not receive data from the power steering ECU with motor assembly for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Main Body ECU
    The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Combination Meter
    The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the air conditioning amplifier assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  14. Combination Meter Assembly / GTS Display "Combination Meter"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Combination Meter Assembly / GTS Display "Combination Meter" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The combination meter assembly does not receive data from the ECM for 2 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 2 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0129
    Lost Communication with Skid Control ECU
    The combination meter assembly does not receive data from the brake actuator assembly for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 3 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0131
    Lost Communication with Power Steering Control Module
    The combination meter assembly does not receive data from the power steering ECU with motor assembly for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 3 seconds.
    EPS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Main Body ECU
    The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 3 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0151
    Lost Communication with Airbag ECU
    The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 10 seconds.
    SRS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0163
    Lost Communication with Navigation Control Module
    The combination meter assembly does not receive data from the navigation receiver assembly for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON.
    2. The power source voltage of the combination meter assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 3 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  15. Navigation Receiver Assembly (for Navigation Receiver Type) / GTS Display "Navigation System"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Navigation Receiver Assembly (for Navigation Receiver Type) / GTS Display "Navigation System" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Sending Malfunction (Navigation to APGS)
    The navigation receiver assembly does not send/receive data 10 times in succession.
    Both conditions are met:
    1. The ignition switch is ACC for 1 second or more.
    2. The power source voltage of the navigation receiver assembly is 9.5 V or more.
    Turn the ignition switch to ACC and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM
    The navigation receiver assembly does not receive data from the ECM for 4 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the navigation receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the navigation receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 4 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Meter ECU Communication
    The navigation receiver assembly does not receive data from the combination meter assembly for 30 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the navigation receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 31 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  16. Radio and Display Receiver Assembly (for Radio and Display Type) / GTS Display "Navigation System"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Radio and Display Receiver Assembly (for Radio and Display Type) / GTS Display "Navigation System" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Sending Malfunction (Navigation to APGS)
    The radio and display receiver assembly does not send/receive data 10 times in succession.
    Both conditions are met:
    1. The ignition switch is ACC for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch to ACC and wait at least 11 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM
    The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 5 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 4 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Meter ECU Communication
    The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the radio and display receiver assembly is 9.5 V or more.
    Turn the ignition switch to ON and wait at least 31 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  17. AFS ECU / GTS Display "AFS"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: Refer to Adaptive Front- Lighting System (Click here).


    AFS ECU / GTS Display "AFS" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0073
    Control Module Communication Bus Off
    The AFS ECU does not send/receive data 10 times in succession.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0100
    Lost Communication with ECM
    The AFS ECU does not receive data from the ECM for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The AFS ECU does not receive data from the TCM for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0126
    Lost Communication with Steering Angle Sensor Module
    The AFS ECU does not receive data from the steering sensor for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 8 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0129
    Lost Communication with Skid Control ECU
    The AFS ECU does not receive data from the brake actuator assembly for 5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Main Body ECU
    The AFS ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.
    U1000*
    Can Communication Failure(Message Registry)
    The AFS ECU does not send/receive data 10 times in succession.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the AFS ECU is 10 V or more.
    Turn the ignition switch to ON and wait at least 13 seconds.
    AFS warning light illuminates.
    DTC is stored until it is cleared using the GTS.

  18. Clearance Warning ECU Assembly / GTS Display "Clearance Sonar"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Clearance Warning ECU Assembly / GTS Display "Clearance Sonar" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The clearance warning ECU assembly does not receive data from the ECM for 5.75 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 2 seconds or more.
    2. The power source voltage of the clearance warning ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 7.75 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0101
    Lost Communication with TCM
    The clearance warning ECU assembly does not receive data from the TCM for 8.07 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 2 seconds or more.
    2. The power source voltage of the clearance warning ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 10.07 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Body Control Module "B"
    The clearance warning ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 5.9 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 2 seconds or more.
    2. The power source voltage of the clearance warning ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 7.9 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0155
    Lost Communication with Instrument Panel Cluster Control Module (Combination Meter)
    The clearance warning ECU assembly does not receive data from the combination meter assembly for 6.5 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 2 seconds or more.
    2. The power source voltage of the clearance warning ECU assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 8.5 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  19. Multiplex Tilt and Telescopic ECU / GTS Display "Tilt & Telescopic"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Multiplex Tilt and Telescopic ECU / GTS Display "Tilt & Telescopic" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0142
    Lost Communication with Main Body ECU
    The multiplex tilt and telescopic ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    The power source voltage of the multiplex tilt and telescopic ECU is 10.1 V or more.
    Turn the ignition switch to ON and wait at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0208
    Lost Communication with "Seat Control Module A"
    The multiplex tilt and telescopic ECU does not receive data from the position control ECU and switch assembly (for driver side) for 10 seconds or more.
    The power source voltage of the multiplex tilt and telescopic ECU is 10.1 V or more.
    Turn the ignition switch to ON and wait at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  20. Position Control ECU and Switch Assembly (for Driver Side) / GTS Display "Driver Seat"

    HINT:
    The position control ECU and switch assembly (for driver side) is connected to the CAN communication system, but the position control ECU and switch assembly (for driver side) does not store or output CAN communication DTCs.

  21. Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror R"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror R" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0142
    Lost Communication with Body Control Module ''B''
    The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  22. Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror L"

    HINT:
    This ECU uses the CAN communication system for DTC communication.


    Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror L" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0142
    Lost Communication with Body Control Module ''B''
    The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more.
    Both conditions are met:
    1. 10 seconds have elapsed after connection of the battery.
    2. The power source voltage of the combination meter assembly is 10 V or more.
    Turn the ignition switch to ON and wait at least 10 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  23. Rear Television Camera Assembly (for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)) / GTS Display "Advanced Parking Guidance/Parking Assist Monitor"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *: The rear television camera assembly stores this DTC if an internal error related to the CAN communication system is detected.
      (Click here)


    Rear Television Camera Assembly (for Radio and Display Type (w/ Parking Assist Monitor System without Parallel Parking Assist Function)) / GTS Display "Advanced Parking Guidance/Parking Assist Monitor" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The rear television camera assembly does not receive data from the ECM for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ON and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0126
    Lost Communication with Steering Angle Sensor Module
    The rear television camera assembly does not receive data from the steering sensor for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ON and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0129
    Lost Communication with Brake System Control Module
    The rear television camera assembly does not receive data from the brake actuator assembly for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ON and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0131
    Lost Communication with Power Steering Control Module
    The rear television camera assembly does not receive data from the power steering ECU with motor assembly for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ACC ON for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ON and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0140
    Lost Communication with Body Control Module
    The rear television camera assembly does not receive data from the main body ECU (multiplex network body ECU) for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ACC for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ACC and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0163
    Lost Communication with Navigation Control Module
    The rear television camera assembly does not receive data from the radio and display receiver assembly for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ACC for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ACC and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U1000*
    CAN Communication Failure (Message Registry)
    When the ignition switch is ACC, a CAN communication malfunction is detected.
    The ignition switch is ACC.
    Turn the ignition switch to ON.
    -
    DTC remains stored only while malfunction is occurring.
    U1110
    Lost Communication with Intuitive Parking Assist Module
    The rear television camera assembly does not receive data from the clearance warning ECU assembly for 11 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 3 seconds or more.
    2. The power source voltage of the rear television camera assembly is 5.5 V or more.
    Turn the ignition switch to ON and wait at least 14 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  24. Inner Rear View Mirror Assembly / GTS Display "-"

    HINT:
    The inner rear view mirror assembly is connected to the CAN communication system, but the inner rear view mirror assembly does not store or output CAN communication DTCs.

  25. Network Gateway ECU / GTS Display "Gateway"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. "Gateway" stores DTCs when a communication error is detected in sub bus 2.


    Network Gateway ECU / GTS Display "Gateway" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0233
    Lost Communication with Blind Spot Monitor Master Module
    The network gateway ECU does not receive data from the blind spot monitor sensor RH for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 11 seconds or more.
    2. The power source voltage of the network gateway ECU is between 9.5 and 10.5 V.
    Turn the ignition switch to ON and wait at least 21 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U0265
    Lost Communication with Parking Assist Monitor Module
    The network gateway ECU does not receive data from the inner rear view mirror assembly for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 11 seconds or more.
    2. The power source voltage of the network gateway ECU is between 9.5 and 10.5 V.
    Turn the ignition switch to ON and wait at least 21 seconds.
    -
    DTC is stored until it is cleared using the GTS.
    U1002
    Lost Communication with Gateway Module (Network Gateway ECU)
    The network gateway ECU does not receive data from the inner rear view mirror assembly and blind spot monitor sensor RH for 10 seconds or more.
    Both conditions are met:
    1. The ignition switch is ON for 11 seconds or more.
    2. The power source voltage of the network gateway ECU is between 9.5 and 10.5 V.
    Turn the ignition switch to ON and wait at least 21 seconds.
    -
    DTC is stored until it is cleared using the GTS.

  26. Blind Spot Monitor Sensor RH / GTS Display "Blind Spot Monitor Master"

    HINT:
    1. This ECU uses the CAN communication system for DTC communication.
    2. *1: Refer to Blind Spot Monitor System (Click here).
    3. *2: Refer to Blind Spot Monitor System (Click here).


    Blind Spot Monitor Sensor RH / GTS Display "Blind Spot Monitor Master" 
    DTC
    Detection Item
    DTC Detection Condition
    DTC Detection Pre-condition
    DTC Check Procedure
    Warning Indication in Meter
    DTC Storage Method
    U0100
    Lost Communication with ECM / PCM "A"
    The blind spot monitor sensor RH does not receive data from the TCM for 10.84 seconds or more.
    All conditions are met:
    1. Blind spot monitor main switch on.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    4. Vehicle speed is 5 km/h (3 mph) or more.
    Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.84 seconds, and then drive the vehicle at a speed of 5 km/h (3 mph) or more.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.
    U0126
    Lost Communication with Steering Angle Sensor Module
    The blind spot monitor sensor RH does not receive data from the steering sensor for 10.68 seconds or more.
    All conditions are met:
    1. Blind spot monitor main switch on.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.68 seconds.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.
    U0129
    Lost Communication with Brake System Control Module
    The blind spot monitor sensor RH does not receive data from the skid control ECU (brake actuator assembly) for 2.334 seconds or more.
    All conditions are met:
    1. Blind spot monitor main switch on.
    2. The ignition switch is ON for 2 seconds or more.
    3. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 4.334 seconds.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.
    U0142
    Lost Communication with Body Control Module "B"
    The blind spot monitor sensor RH does not receive data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more.
    All conditions are met:
    1. Blind spot monitor main switch on.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), wait at least 11.6 seconds.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.
    U0232*1
    Lost Communication with Blind Spot Monitor Slave Module
    The blind spot monitor sensor RH does not receive data from the blind spot monitor sensor LH for 10.6 seconds or more.
    All conditions are met:
    1. The ignition switch is ON for 1 second or more.
    2. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    Turn the ignition switch to ON and wait at least 11.6 seconds.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.
    U1331*2
    Software Incompatibility with Body Control Module "B"
    Destination information of the main body ECU and blind spot monitor sensor do not match.
    All conditions are met:
    1. Blind spot monitor main switch on.
    2. The ignition switch is ON for 1 second or more.
    3. The power source voltage of the blind spot monitor sensor RH is 10 V or more.
    Destination information of the main body ECU and blind spot monitor sensor do not match.
    Displays messages on the multi-information display
    DTC is stored until it is cleared using the GTS.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF V BUS, PAST COMMUNICATION ERROR)
  1. Regarding a past communication error of an ECU or sensor connected to the V bus (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), the probable CAN branch that had a malfunction can be determined based on the following DTC combination table.

    HINT:
    1. Based on the table below and DTCs output from ECUs connected via CAN communication, the probable part for which communication stop occurred can be determined.
    2. Regarding an open in a CAN branch and a communication stop that is currently occurring, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS because the ECU or sensor connected to the CAN branch does not respond (the ECU or sensor name will not be displayed on the screen).
    3. If an open in a CAN main bus line, a short between the CAN bus lines (CANH and CANL) or a +B or ground short in the CAN bus occurs, DTCs of almost all ECUs (or sensors) on the CAN bus may be output, or a message indicating a communication error may be displayed on the GTS screen. In this case, check the resistance of the CAN bus (steps 7 to 9) first (Click here).
    4. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


    for LHD 
    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    AFS ECU Communication Stop Mode (Click here)
    Navigation ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    โ—‹
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    โ—‹
    -
    -
    U0155
    -
    โ—‹
    -
    -
    AFS ECU*2
    U0100
    -
    -
    โ—‹
    -
    U0101
    -
    -
    โ—‹
    -
    U0126
    -
    -
    โ—‹
    -
    U0129
    -
    -
    โ—‹
    -
    U0142
    -
    -
    โ—‹
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    โ—‹
    U0140
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    โ—‹
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    โ—‹
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    V Bus
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    โ—‹
    -
    -
    -
    U0163
    -
    -
    -
    โ—‹
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    โ—‹
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    Clearance Warning ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    โ—‹
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    โ—‹
    -
    -
    U0140
    โ—‹
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    โ—‹
    -
    U0101
    -
    โ—‹
    -
    U0120
    -
    โ—‹
    -
    U0151
    -
    โ—‹
    -
    U0155
    -
    โ—‹
    -
    U0164
    -
    โ—‹
    -
    U023A
    -
    โ—‹
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0142
    -
    โ—‹
    โ—‹
    U0155
    -
    -
    โ—‹
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0163
    โ—‹
    -
    -
    V Bus
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    -
    -
    U0126
    โ—‹
    -
    -
    U0129
    โ—‹
    -
    -
    U0131
    โ—‹
    -
    -
    U0140
    โ—‹
    โ—‹
    -
    U0163
    โ—‹
    -
    -
    U1110
    โ—‹
    -
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    U0200
    -
    -
    -
    U0208
    -
    -
    -
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    V Bus
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    โ—‹
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0155
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0120
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0155
    -
    -
    -
    U0164
    -
    -
    -
    U023A
    -
    -
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    โ—‹
    -
    -
    U0129
    โ—‹
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    X
    โ—‹
    -
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    โ—‹
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    X
    -
    -
    U0131
    โ—‹
    -
    -
    U0142
    -
    -
    -
    U0151
    -
    -
    -
    U0163
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    V Bus
    Brake Actuator Assembly*2
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0131
    โ—‹
    -
    -
    U0140
    -
    -
    -
    U0163
    -
    -
    -
    U1110
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    U0200
    -
    -
    -
    U0208
    -
    -
    -
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Skid Control ECU Communication Stop Mode (Click here)
    DLC3
    Gateway ECU Communication Stop Mode (Click here)
    Front Camera Module Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    V Bus
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0142
    -
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    โ—‹
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    X
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    V Bus
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    โ—‹
    -
    -
    U0123
    โ—‹
    โ—‹
    -
    -
    U0126
    โ—‹
    โ—‹
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    5. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    AFS ECU Communication Stop Mode (Click here)
    Navigation ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    โ—‹
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    โ—‹
    -
    -
    U0155
    -
    โ—‹
    -
    -
    AFS ECU*2
    U0100
    -
    -
    โ—‹
    -
    U0101
    -
    -
    โ—‹
    -
    U0126
    -
    -
    โ—‹
    -
    U0129
    -
    -
    โ—‹
    -
    U0142
    -
    -
    โ—‹
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    โ—‹
    U0140
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    โ—‹
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    โ—‹
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    V Bus
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    โ—‹
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    -
    U0123
    โ—‹
    -
    -
    -
    U0126
    -
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    Clearance Warning ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    โ—‹
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    โ—‹
    -
    -
    U0140
    โ—‹
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    โ—‹
    -
    U0101
    -
    โ—‹
    -
    U0120
    -
    โ—‹
    -
    U0151
    -
    โ—‹
    -
    U0155
    -
    โ—‹
    -
    U0164
    -
    โ—‹
    -
    U023A
    -
    -
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0142
    -
    โ—‹
    โ—‹
    U0155
    -
    -
    โ—‹
    V Bus
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0163
    โ—‹
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    U0123
    -
    -
    -
    U0126
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0140
    -
    โ—‹
    -
    U0163
    โ—‹
    -
    -
    U1110
    -
    -
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    U0200
    -
    -
    -
    U0208
    -
    -
    -
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    โ—‹
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0155
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0120
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0155
    -
    -
    -
    U0164
    -
    -
    -
    U023A
    -
    -
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    ECM
    -
    -
    -
    -
    V Bus
    Power Steering ECU with Motor Assembly
    U0100
    โ—‹
    -
    -
    U0129
    โ—‹
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    โ—‹
    -
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    -
    โ—‹
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    โ—‹
    -
    -
    U0142
    -
    -
    -
    U0151
    -
    -
    -
    U0163
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    โ—‹
    U0123
    -
    -
    -
    U0126
    -
    -
    โ—‹
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0131
    โ—‹
    -
    -
    U0140
    -
    -
    -
    U0163
    -
    -
    -
    U1110
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    โ—‹
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    U0200
    -
    -
    -
    U0208
    -
    -
    -
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Skid Control ECU Communication Stop Mode (Click here)
    DLC3
    Gateway ECU Communication Stop Mode (Click here)
    Front Camera Module Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0142
    -
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    โ—‹
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    V Bus
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    -
    -
    -
    U0123
    โ—‹
    -
    -
    -
    U0126
    โ—‹
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    โ—‹
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in One CAN Main Bus Line)
    V Bus
    Output ECU
    Output DTC
    Combination Meter ECU Communication Stop Mode (Click here)
    CAN No. 1 J/C to CAN No. 2 J/C
    ECM Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    โ—‹
    U0131
    -
    -
    โ—‹
    U0142
    -
    โ—‹
    -
    U0155
    -
    โ—‹
    -
    AFS ECU*2
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0126
    -
    -
    -
    U0129
    -
    โ—‹
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    โ—‹
    U0140
    X
    โ—‹
    -
    U0155
    โ—‹
    โ—‹
    -
    V Bus
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0120
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0155
    โ—‹
    -
    -
    U0164
    -
    โ—‹
    -
    U023A
    X
    X
    X
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    โ—‹
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    โ—‹
    โ—‹
    U0129
    -
    โ—‹
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    โ—‹
    U0140
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Combination Meter Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    -
    U0131
    โ—‹
    -
    -
    U0142
    โ—‹
    -
    -
    U0151
    โ—‹
    -
    -
    U0163
    -
    X
    X
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    X
    X
    X
    U0126
    X
    X
    X
    U0129
    X
    X
    X
    U0131
    X
    X
    X
    U0140
    X
    X
    X
    U0163
    X
    X
    X
    U1110
    X
    X
    X
    Blind Spot Monitor Sensor RH
    U0100
    X
    X
    X
    U0126
    X
    X
    X
    U0129
    X
    X
    X
    U0142
    X
    X
    X
    Sub Bus 2
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    X
    X
    X
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    X
    X
    X
    U0200
    X
    X
    X
    U0208
    X
    X
    X
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    X
    X
    X
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    X
    X
    X
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    5. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Main Bus Lines)
    V Bus
    Output ECU
    Output DTC
    Combination Meter ECU Communication Stop Mode (Click here)
    CAN No. 1 J/C to CAN No. 2 J/C
    ECM Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    โ—‹
    U0131
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    โ—‹
    -
    V Bus
    AFS ECU*2
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0126
    -
    -
    -
    U0129
    -
    โ—‹
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    โ—‹
    U0140
    -
    โ—‹
    -
    U0155
    โ—‹
    โ—‹
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0120
    -
    โ—‹
    -
    U0151
    -
    -
    -
    U0155
    โ—‹
    -
    -
    U0164
    -
    โ—‹
    -
    U023A
    -
    -
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    โ—‹
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    โ—‹
    โ—‹
    U0129
    -
    โ—‹
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    โ—‹
    U0140
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Combination Meter Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    -
    U0131
    โ—‹
    -
    -
    U0142
    โ—‹
    -
    -
    U0151
    โ—‹
    -
    -
    U0163
    โ—‹
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    โ—‹
    โ—‹
    U0123
    -
    โ—‹
    -
    U0126
    -
    โ—‹
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    V Bus
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    โ—‹
    โ—‹
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0140
    -
    -
    -
    U0163
    -
    -
    -
    U1110
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    U0208
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    U0200
    -
    -
    -
    U0208
    -
    -
    -
    U1002
    -
    -
    -
    U1115
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
    V Bus
    Output ECU
    Output DTC
    CAN No. 1 J/C to CAN No. 2 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    V Bus
    Air Conditioning Amplifier Assembly
    U0100
    โ—‹
    U0131
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    AFS ECU*2
    U0100
    โ—‹
    U0101
    โ—‹
    U0126
    โ—‹
    U0129
    โ—‹
    U0142
    โ—‹
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    โ—‹
    U0140
    โ—‹
    U0155
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    โ—‹
    U0101
    โ—‹
    U0120
    โ—‹
    U0151
    โ—‹
    U0155
    โ—‹
    U0164
    โ—‹
    U023A
    โ—‹
    U0327
    โ—‹
    Clearance Warning ECU Assembly
    U0100
    โ—‹
    U0101
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    ECM
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    โ—‹
    U0129
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    โ—‹
    U0140
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    Combination Meter Assembly
    U0100
    โ—‹
    U0129
    โ—‹
    U0131
    โ—‹
    U0142
    โ—‹
    U0151
    โ—‹
    U0163
    โ—‹
    Steering Sensor
    -
    -
    Brake Actuator Assembly*2
    U0100
    โ—‹
    U0123
    โ—‹
    U0126
    โ—‹
    Network Gateway ECU*1
    -
    -
    V Bus
    Inner Rear View Mirror Assembly
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    U0126
    โ—‹
    U0129
    โ—‹
    U0131
    โ—‹
    U0140
    โ—‹
    U0163
    โ—‹
    U1110
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    โ—‹
    U0126
    โ—‹
    U0129
    โ—‹
    U0142
    โ—‹
    Network Gateway ECU*1
    U0233
    -
    U0265
    -
    U1002
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    U0208
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    โ—‹
    U0200
    โ—‹
    U0208
    โ—‹
    U1002
    -
    U1115
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    โ—‹
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    โ—‹
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for RHD 
    -
    Trouble Mode
    V Bus (Open in One CAN Branch Line)
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    V Bus
    Air Conditioning Amplifier Assembly
    U0100
    -
    โ—‹
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    โ—‹
    -
    โ—‹
    U0155
    -
    โ—‹
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    โ—‹
    -
    U0140
    -
    -
    โ—‹
    โ—‹
    U0155
    -
    -
    โ—‹
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    -
    โ—‹
    U0101
    -
    -
    -
    โ—‹
    U0120
    -
    -
    -
    โ—‹
    U0151
    โ—‹
    -
    -
    โ—‹
    U0155
    -
    -
    -
    โ—‹
    U0164
    -
    โ—‹
    -
    โ—‹
    U0327
    -
    -
    -
    โ—‹
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    โ—‹
    U0142
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    โ—‹
    U0151
    โ—‹
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹

    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Clearance Warning ECU Communication Stop Mode (Click here)
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    โ—‹
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U0327
    -
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    โ—‹
    -
    -
    -
    U0101
    โ—‹
    -
    -
    -
    U0142
    โ—‹
    -
    -
    -
    U0155
    โ—‹
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    โ—‹
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    โ—‹
    -
    U0140
    -
    -
    โ—‹
    -
    U0142
    -
    -
    โ—‹
    -
    U0155
    -
    -
    โ—‹
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹

    -
    Trouble Mode (Open in One CAN Branch Line)
    V Bus
    Output ECU
    Output DTC
    Skid Control ECU Communication Stop Mode (Click here)
    DLC3
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    U0140
    -
    -
    U0155
    -
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    U0101
    -
    -
    U0120
    -
    -
    U0151
    -
    -
    U0155
    -
    -
    U0164
    -
    -
    U0327
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    U0101
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    ECM
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    U0129
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    U0140
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    U0129
    โ—‹
    โ—‹
    U0131
    -
    -
    U0142
    -
    -
    U0151
    -
    -
    U0163
    -
    -
    Steering Sensor
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *: DTC U0073 may be stored when communication is lost.


    for RHD 
    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Center Airbag Sensor Communication Stop Mode (Click here)
    Air Conditioning Amplifier Communication Stop Mode (Click here)
    Audio Receiver Assembly Communication Stop Mode (Click here)
    Main Body ECU Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    โ—‹
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    โ—‹
    -
    โ—‹
    U0155
    -
    โ—‹
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    โ—‹
    -
    U0140
    -
    -
    โ—‹
    โ—‹
    U0155
    -
    -
    โ—‹
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    -
    โ—‹
    U0101
    -
    -
    -
    โ—‹
    U0120
    -
    -
    -
    โ—‹
    U0151
    โ—‹
    -
    -
    โ—‹
    U0155
    -
    -
    -
    โ—‹
    U0164
    -
    โ—‹
    -
    โ—‹
    U0327
    -
    -
    -
    โ—‹
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    โ—‹
    U0142
    -
    -
    -
    โ—‹
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    โ—‹
    U0151
    โ—‹
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    -
    -
    -
    -
    U0123
    โ—‹
    -
    -
    -
    U0126
    -
    -
    -
    -

    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Clearance Warning ECU Communication Stop Mode (Click here)
    Power Steering ECU Communication Stop Mode (Click here)
    Certification ECU Communication Stop Mode (Click here)
    Steering Angle Sensor Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    โ—‹
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U0327
    -
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    โ—‹
    -
    -
    -
    U0101
    โ—‹
    -
    -
    -
    U0142
    โ—‹
    -
    -
    -
    U0155
    โ—‹
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    โ—‹
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    โ—‹
    -
    U0140
    -
    -
    โ—‹
    -
    U0142
    -
    -
    โ—‹
    -
    U0155
    -
    -
    โ—‹
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    -
    โ—‹
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    -
    -
    -
    โ—‹
    U0123
    -
    -
    -
    -
    U0126
    -
    -
    -
    โ—‹

    -
    Trouble Mode (Open in Both CAN Branch Lines)
    V Bus
    Output ECU
    Output DTC
    Skid Control ECU Communication Stop Mode (Click here)
    DLC3
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    U0140
    -
    -
    U0155
    -
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    U0101
    -
    -
    U0120
    -
    -
    U0151
    -
    -
    U0155
    -
    -
    U0164
    -
    -
    U0327
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    U0101
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    ECM
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    U0129
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    U0140
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    U0129
    โ—‹
    โ—‹
    U0131
    -
    -
    U0142
    -
    -
    U0151
    -
    -
    U0163
    -
    -
    Steering Sensor
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    -
    U0123
    โ—‹
    -
    U0126
    โ—‹
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *: DTC U0073 may be stored when communication is lost.


    for RHD 
    -
    Trouble Mode (Open in One CAN Main Bus Line)
    V Bus
    Output ECU
    Output DTC
    Combination Meter ECU Communication Stop Mode (Click here)
    CAN No. 1 J/C to CAN No. 2 J/C
    ECM Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    โ—‹
    U0131
    -
    -
    โ—‹
    U0142
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    โ—‹
    U0140
    X
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0120
    -
    -
    -
    U0151
    -
    -
    -
    U0155
    โ—‹
    -
    -
    U0164
    -
    โ—‹
    -
    U0327
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    โ—‹
    โ—‹
    U0129
    -
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    โ—‹
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    Combination Meter Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    U0131
    โ—‹
    โ—‹
    -
    U0142
    โ—‹
    โ—‹
    -
    U0151
    โ—‹
    โ—‹
    -
    U0163
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0123
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹

    HINT:
    1. โ—‹: Set
    2. X: Not set or may be set according to the malfunctioning part when one line of a CAN branch is open.
    3. -: DTC is not output.
    4. *: DTC U0073 may be stored when communication is lost.


    for RHD 
    -
    Trouble Mode (Open in Both CAN Main Bus Lines)
    V Bus
    Output ECU
    Output DTC
    Combination Meter ECU Communication Stop Mode (Click here)
    CAN No. 1 J/C to CAN No. 2 J/C
    ECM Communication Stop Mode (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    โ—‹
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    -
    -
    โ—‹
    U0140
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    -
    -
    โ—‹
    U0101
    -
    -
    โ—‹
    U0120
    -
    -
    -
    U0151
    -
    -
    -
    U0155
    โ—‹
    โ—‹
    -
    U0164
    -
    -
    -
    U0327
    -
    โ—‹
    -
    Clearance Warning ECU Assembly
    U0100
    -
    โ—‹
    โ—‹
    U0101
    -
    โ—‹
    โ—‹
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    โ—‹
    โ—‹
    U0140
    -
    โ—‹
    -
    U0142
    -
    โ—‹
    -
    U0155
    โ—‹
    -
    -
    Combination Meter Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    U0131
    โ—‹
    โ—‹
    -
    U0142
    โ—‹
    โ—‹
    -
    U0151
    โ—‹
    โ—‹
    -
    U0163
    โ—‹
    โ—‹
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*
    U0100
    -
    โ—‹
    โ—‹
    U0123
    -
    โ—‹
    -
    U0126
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *: DTC U0073 may be stored when communication is lost.


    for RHD 
    -
    Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
    V Bus
    Output ECU
    Output DTC
    CAN No. 1 J/C to CAN No. 2 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    โ—‹
    U0131
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    Radio and Display Receiver Assembly (for Radio and Display Type)*
    U0100
    โ—‹
    U0140
    โ—‹
    U0155
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)
    U0100
    โ—‹
    U0101
    โ—‹
    U0120
    โ—‹
    U0151
    โ—‹
    U0155
    โ—‹
    U0164
    โ—‹
    U0327
    โ—‹
    Clearance Warning ECU Assembly
    U0100
    โ—‹
    U0101
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    ECM
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    โ—‹
    U0129
    โ—‹
    Smart Key ECU Assembly (Certification ECU)
    U0100
    โ—‹
    U0140
    โ—‹
    U0142
    โ—‹
    U0155
    โ—‹
    Combination Meter Assembly
    U0100
    โ—‹
    U0129
    โ—‹
    U0131
    โ—‹
    U0142
    โ—‹
    U0151
    โ—‹
    U0163
    โ—‹
    Steering Sensor
    -
    -
    Brake Actuator Assembly*
    U0100
    โ—‹
    U0123
    โ—‹
    U0126
    โ—‹

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *: DTC U0073 may be stored when communication is lost.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 1, PAST COMMUNICATION ERROR)
  1. Regarding a past communication error of ECUs and sensors connected to sub bus 1 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the main body ECU (multiplex network body ECU).

    HINT:
    1. As gateway function equipped ECUs (sub bus monitor ECUs) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
    2. DTCs output from ECUs other than the main body ECU (multiplex network body ECU) (gateway function equipped ECU) are shown only as a reference.
    3. Regarding a communication stop that is currently occurring in sub bus 1, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
    4. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


    for LHD 
    -
    Trouble Mode (Open in One CAN Branch Line)
    Sub Bus 1
    Output ECU
    Output DTC
    Multiplex Tilt and Telescopic ECU (Click here)
    Outer Mirror Control ECU Assembly (for Driver Side) (Click here)
    Outer Mirror Control ECU Assembly (for Front Passenger Side) (Click here)
    Position Control ECU and Switch Assembly (for Driver Side) (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    V Bus
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    โ—‹
    -
    -
    -
    U0208
    โ—‹
    -
    -
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    โ—‹
    -
    -
    U0200
    -
    -
    โ—‹
    -
    U0208
    -
    -
    -
    โ—‹
    U1002
    โ—‹
    -
    -
    -
    U1115
    โ—‹
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Branch Lines)
    Sub Bus 1
    Output ECU
    Output DTC
    Multiplex Tilt and Telescopic ECU (Click here)
    Outer Mirror Control ECU Assembly (for Driver Side) (Click here)
    Outer Mirror Control ECU Assembly (for Front Passenger Side) (Click here)
    Position Control ECU and Switch Assembly (for Driver Side) (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    V Bus
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    U1110
    -
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    -
    U0265
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    โ—‹
    -
    -
    -
    U0208
    โ—‹
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    โ—‹
    -
    -
    U0200
    -
    -
    โ—‹
    -
    U0208
    -
    -
    -
    โ—‹
    U1002
    โ—‹
    -
    -
    -
    U1115
    โ—‹
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Sub Bus 1
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in One CAN Main Bus Line)
    Sub Bus 1
    Output ECU
    Output DTC
    Main Body ECU (Multiplex Network Body ECU) (Click here)
    CAN No. 3 J/C to CAN No. 4 J/C
    CAN No. 5 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0155
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0120
    -
    -
    -
    U0151
    -
    -
    -
    U0155
    -
    -
    -
    U0164
    -
    -
    -
    U023A
    -
    -
    -
    U0327
    -
    -
    -
    V Bus
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0151
    -
    -
    -
    U0163
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    U0123
    -
    -
    -
    U0126
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0140
    -
    -
    -
    U0163
    -
    -
    -
    U1110
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    โ—‹
    -
    -
    U0208
    โ—‹
    โ—‹
    โ—‹
    Sub Bus 1
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    โ—‹
    โ—‹
    โ—‹
    U0200
    โ—‹
    โ—‹
    โ—‹
    U0208
    โ—‹
    โ—‹
    โ—‹
    U1002
    โ—‹
    โ—‹
    โ—‹
    U1115
    โ—‹
    โ—‹
    โ—‹
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    โ—‹
    โ—‹
    โ—‹
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    โ—‹
    โ—‹
    โ—‹
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Main Bus Lines)
    Sub Bus 1
    Output ECU
    Output DTC
    Main Body ECU (Multiplex Network Body ECU) (Click here)
    CAN No. 3 J/C to CAN No. 4 J/C
    CAN No. 5 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0155
    -
    -
    -
    V Bus
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    U0101
    -
    -
    -
    U0120
    -
    -
    -
    U0151
    -
    -
    -
    U0155
    -
    -
    -
    U0164
    -
    -
    -
    U023A
    -
    -
    -
    U0327
    -
    -
    -
    Clearance Warning ECU Assembly
    U0073
    -
    -
    -
    U0101
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    ECM
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    U0140
    -
    -
    -
    U0142
    -
    -
    -
    U0155
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0142
    -
    -
    -
    U0151
    -
    -
    -
    U0163
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    U0123
    -
    -
    -
    U0126
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0131
    -
    -
    -
    U0140
    -
    -
    -
    U0163
    -
    -
    -
    U1110
    -
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    -
    U0126
    -
    -
    -
    U0129
    -
    -
    -
    U0142
    -
    -
    -
    Sub Bus 2
    Network Gateway ECU*1
    U0233
    -
    -
    -
    U0265
    -
    -
    -
    U1002
    -
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    โ—‹
    -
    -
    U0208
    โ—‹
    โ—‹
    โ—‹
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    โ—‹
    โ—‹
    โ—‹
    U0200
    โ—‹
    โ—‹
    โ—‹
    U0208
    โ—‹
    โ—‹
    โ—‹
    U1002
    โ—‹
    -
    -
    U1115
    โ—‹
    โ—‹
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    โ—‹
    โ—‹
    โ—‹
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    โ—‹
    โ—‹
    โ—‹
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
    Sub Bus 1
    Output ECU
    Output DTC
    CAN No. 3 J/C to CAN No. 4 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    U0131
    -
    U0142
    -
    U0155
    -
    AFS ECU*2
    U0100
    -
    U0101
    -
    U0126
    -
    U0129
    -
    U0142
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    U0140
    -
    U0155
    -
    V Bus
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    U0101
    -
    U0120
    -
    U0151
    -
    U0155
    -
    U0164
    -
    U023A
    -
    U0327
    -
    Clearance Warning ECU Assembly
    U0100
    -
    U0101
    -
    U0142
    -
    U0155
    -
    ECM
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    U0129
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    U0140
    -
    U0142
    -
    U0155
    -
    Combination Meter Assembly
    U0100
    -
    U0129
    -
    U0131
    -
    U0142
    -
    U0151
    -
    U0163
    -
    Steering Sensor
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    U0123
    -
    U0126
    -
    Network Gateway ECU*1
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    U0126
    -
    U0129
    -
    U0131
    -
    U0140
    -
    U0163
    -
    U1110
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    U0126
    -
    U0129
    -
    U0142
    -
    Network Gateway ECU*1
    U0233
    -
    U0265
    -
    U1002
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    U0208
    โ—‹
    Sub Bus 1
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    โ—‹
    U0200
    โ—‹
    U0208
    โ—‹
    U1002
    โ—‹
    U1115
    โ—‹
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    โ—‹
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    โ—‹
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


DTC COMBINATION TABLE (OPEN IN CAN BRANCH OF SUB BUS 2, PAST COMMUNICATION ERROR)
  1. Regarding a past communication error of ECUs and sensors connected to sub bus 2 (in this case, normal is displayed when performing the CAN bus check, but communication DTCs are output), determine the part that had a malfunction based on DTCs output from the network gateway ECU.

    HINT:
    1. As gateway function equipped ECUs (sub bus monitor ECUs) monitor signals from all ECUs that are connected to sub buses, gateway function equipped ECUs can detect ECUs with a communication stop more accurately.
    2. DTCs output from ECUs other than the network gateway ECU (gateway function equipped ECU) are shown only as a reference.
    3. Regarding a communication stop that is currently occurring in sub bus 2, the malfunctioning part can be confirmed easily by performing the CAN bus check using the GTS.
    4. If an open occurs in just one of the lines of a CAN branch, DTCs which are not related to malfunctioning parts may be output (DTCs may be displayed randomly), or a message indicating a communication error may be displayed.


    for LHD 
    -
    Trouble Mode (Open in one CAN Branch Line)
    Sub bus 2
    Output ECU
    Output DTC
    Rear Television Camera Assembly (Click here)
    Blind Spot Monitor Sensor RH (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    AFS ECU*2
    U0100
    -
    -
    U0101
    -
    -
    U0126
    -
    -
    U0129
    -
    -
    U0142
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    U0140
    -
    -
    U0155
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    U0101
    -
    -
    U0120
    -
    -
    U0151
    -
    -
    U0155
    -
    -
    U0164
    -
    -
    U023A
    -
    -
    U0327
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    U0101
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    ECM
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    U0129
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    U0140
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    U0129
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0151
    -
    -
    U0163
    -
    -
    V Bus
    Steering Sensor
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    U0123
    -
    -
    U0126
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    -
    -
    U0126
    -
    -
    U0129
    -
    -
    U0131
    -
    -
    U0140
    -
    -
    U0163
    -
    -
    U1110
    -
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    -
    U0126
    -
    -
    U0129
    -
    -
    U0142
    -
    -
    Network Gateway ECU*1
    U0233
    -
    โ—‹
    U0265
    โ—‹
    -
    U1002
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    U0208
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    U0200
    -
    -
    U0208
    -
    -
    U1002
    -
    -
    U1115
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Branch Lines)
    Sub bus 2
    Output ECU
    Output DTC
    Rear Television Camera Assembly (Click here)
    Blind Spot Monitor Sensor RH (Click here)
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    AFS ECU*2
    U0100
    -
    -
    U0101
    -
    -
    U0126
    -
    -
    U0129
    -
    -
    U0142
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    U0140
    -
    -
    U0155
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    U0101
    -
    -
    U0120
    -
    -
    U0151
    -
    -
    U0155
    -
    -
    U0164
    -
    -
    U023A
    -
    -
    U0327
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    U0101
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    ECM
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    U0129
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    U0140
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    U0129
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0151
    -
    -
    U0163
    -
    -
    V Bus
    Steering Sensor
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    U0123
    -
    -
    U0126
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    -
    U0126
    โ—‹
    -
    U0129
    โ—‹
    -
    U0131
    โ—‹
    -
    U0140
    โ—‹
    -
    U0163
    โ—‹
    -
    U1110
    โ—‹
    -
    Blind Spot Monitor Sensor RH
    U0100
    -
    โ—‹
    U0126
    -
    โ—‹
    U0129
    -
    โ—‹
    U0142
    -
    โ—‹
    Network Gateway ECU*1
    U0233
    -
    โ—‹
    U0265
    โ—‹
    -
    U1002
    -
    -
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    U0208
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    U0200
    -
    -
    U0208
    -
    -
    U1002
    -
    -
    U1115
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in One CAN Main Bus Line)
    Sub bus 2
    Output ECU
    Output DTC
    Network Gateway ECU (Click here)
    CAN No. 6 J/C to CAN No. 7 J/C
    CAN No. 7 J/C to CAN No. 8 J/C
    CAN No. 9 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    V Bus
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0140
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0163
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U1110
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0142
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    U0233
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0265
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U1002
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (Open in Both CAN Main Bus Lines)
    Sub bus 2
    Output ECU
    Output DTC
    Network Gateway ECU (Click here)
    CAN No. 6 J/C to CAN No. 7 J/C
    CAN No. 7 J/C to CAN No. 8 J/C
    CAN No. 9 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    AFS ECU*2
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0120
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    U0164
    -
    -
    -
    -
    U023A
    -
    -
    -
    -
    U0327
    -
    -
    -
    -
    Clearance Warning ECU Assembly
    U0073
    -
    -
    -
    -
    U0101
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    ECM
    -
    -
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    V Bus
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    -
    -
    U0140
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0155
    -
    -
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    -
    -
    U0129
    -
    -
    -
    -
    U0131
    -
    -
    -
    -
    U0142
    -
    -
    -
    -
    U0151
    -
    -
    -
    -
    U0163
    -
    -
    -
    -
    Steering Sensor
    -
    -
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    -
    -
    U0123
    -
    -
    -
    -
    U0126
    -
    -
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0131
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0140
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0163
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U1110
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0142
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Network Gateway ECU*1
    U0233
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U0265
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    U1002
    โ—‹
    โ—‹
    โ—‹
    โ—‹
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    -
    -
    U0200
    -
    -
    -
    -
    U0208
    -
    -
    -
    -
    U1002
    -
    -
    -
    -
    U1115
    -
    -
    -
    -
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


    for LHD 
    -
    Trouble Mode (CAN Bus Line Short Circuit or Short to GND)
    Sub bus 2
    Output ECU
    Output DTC
    CAN No. 6 J/C to CAN No. 7 J/C
    CAN No. 7 J/C to CAN No. 8 J/C
    V Bus
    Airbag Sensor Assembly
    -
    -
    -
    Air Conditioning Amplifier Assembly
    U0100
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    AFS ECU*2
    U0100
    -
    -
    U0101
    -
    -
    U0126
    -
    -
    U0129
    -
    -
    U0142
    -
    -
    1. Navigation Receiver Assembly (for Navigation Receiver Type)*2
    2. Radio and Display Receiver Assembly (for Radio and Display Type)*2
    U0100
    -
    -
    U0140
    -
    -
    U0155
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0100
    -
    -
    U0101
    -
    -
    U0120
    -
    -
    U0151
    -
    -
    U0155
    -
    -
    U0164
    -
    -
    U023A
    -
    -
    U0327
    -
    -
    V Bus
    Clearance Warning ECU Assembly
    U0100
    -
    -
    U0101
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    ECM
    -
    -
    -
    Power Steering ECU with Motor Assembly
    U0100
    -
    -
    U0129
    -
    -
    Smart Key ECU Assembly (Certification ECU)
    U0100
    -
    -
    U0140
    -
    -
    U0142
    -
    -
    U0155
    -
    -
    Combination Meter Assembly
    U0100
    -
    -
    U0129
    -
    -
    U0131
    -
    -
    U0142
    -
    -
    U0151
    -
    -
    U0163
    -
    -
    Steering Sensor
    -
    -
    -
    Brake Actuator Assembly*2
    U0100
    -
    -
    U0123
    -
    -
    U0126
    -
    -
    Network Gateway ECU*1
    -
    -
    -
    Inner Rear View Mirror Assembly
    -
    -
    -
    Sub Bus 2
    Rear Television Camera Assembly
    U0100
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    U0131
    โ—‹
    โ—‹
    U0140
    โ—‹
    โ—‹
    U0163
    โ—‹
    โ—‹
    U1110
    โ—‹
    โ—‹
    Blind Spot Monitor Sensor RH
    U0100
    โ—‹
    โ—‹
    U0126
    โ—‹
    โ—‹
    U0129
    โ—‹
    โ—‹
    U0142
    โ—‹
    โ—‹
    Network Gateway ECU*1
    U0233
    โ—‹
    โ—‹
    U0265
    โ—‹
    โ—‹
    U1002
    โ—‹
    โ—‹
    Sub Bus 1
    Multiplex Tilt and Telescopic ECU
    U0142
    -
    -
    U0208
    -
    -
    Main Body ECU (Multiplex Network Body ECU)*1
    U0199
    -
    -
    U0200
    -
    -
    U0208
    -
    -
    U1002
    -
    -
    U1115
    -
    -
    Sub Bus 1
    Outer Mirror Control ECU Assembly (for Driver Side)
    U0142
    -
    -
    Outer Mirror Control ECU Assembly (for Front Passenger Side)
    U0142
    -
    -
    Position Control ECU and Switch Assembly (for Driver Side)
    -
    -
    -

    HINT:
    1. โ—‹: Set
    2. -: DTC is not output.
    3. *1: Gateway function equipped ECUs relay signals between the ECUs connected to the different buses.
    4. *2: DTC U0073 may be stored when communication is lost.


CAN BUS WAVEFORMS

C230845E02

HINT:
  1. This waveform is measured between terminals CANH and GND, and terminals CANL and GND of the DLC3. (Use this as a reference for diagnosis of CAN communication lines.)
  2. When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first (Click here). If no problems are found, check the following waveforms.
  3. If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
  4. Wiggle the connector and wire harness to check if the waveform changes.



  1. CAN bus waveforms (Group 1)



      C227926E04
    1. Normal waveform



    2. C239096E02
    3. Open in both of the lines (CANH and CANL) of a CAN branch

      HINT:
      1. Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
      2. Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.



    4. C227930E02
    5. Short between the CAN bus lines (CANH and CANL)

      HINT:
      1. Waveforms disappear.
      2. If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.



  2. CAN bus waveforms (reference) (Group 2)

    NOTICE:
    The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.




      C227931E03
    1. Open in a CAN branch line (CANH)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    2. C227932E02
    3. Open in a CAN branch line (CANL)

      HINT:
      1. An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
      2. Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.



    4. C227927E02
    5. Open in a CAN main bus line (CANH)

      HINT:
      1. Waveforms of ECUs or sensors that are closer to the DLC3 than the open part are almost normal.
      2. Waveforms of ECUs or sensors that are on the opposite side of the DLC3 from the open part are abnormal.
      3. An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.



    6. C227928E02
    7. Short between a CAN bus line (CANH) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
      2. A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.



    8. C227929E02
    9. Short between a CAN bus line (CANL) and ground

      HINT:
      1. Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
      2. A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.


DATA SENDING/RECEIVING TABLE
  1. Data sending/receiving table

    HINT:
    If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.

    Data content
    Data Detected and Sent by
    Data Received by
    (Can be Checked in the Data List)
    Data Received by
    (Cannot be Checked in the Data List)
    Relevant Data List Item
    [Selected System]
    Accelerator position
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    Brake actuator assembly
    Airbag sensor assembly
    1. Accelerator Position (2AR-FE) [Engine and ECT]
    2. Accelerator Position (2GR-FE/6AR-FSE) [Engine]
    3. Accelerator Opening Angle % [ABS/VSC/TRC]
    Engine speed
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    1. Power steering ECU with motor assembly
    2. Brake actuator assembly
    3. Combination meter assembly
    4. Smart key ECU assembly (Certification ECU)
    1. Airbag sensor assembly
    2. Air conditioning amplifier assembly
    3. Navigation receiver assembly
    4. Radio and display receiver assembly
    5. Main body ECU (Multiplex network body ECU)
    1. Engine Speed (2AR-FE) [Engine and ECT]
    2. Engine Speed (2GR-FE/6AR-FSE) [Engine]
    3. Engine Revolutions [ABS/VSC/TRC]
    4. Engine Rpm [Combination Meter]
    5. Engine Speed [Starting Control]
    Engine coolant temperature
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    1. Air conditioning amplifier assembly
    2. Combination meter assembly
    -
    1. Coolant Temp (2AR-FE) [Engine and ECT]
    2. Coolant Temp (2GR-FE/6AR-FSE) [Engine]
    3. Engine Coolant Temp [Air Conditioner]
    4. Coolant Temperature [Combination Meter]
    Vehicle speed
    Brake actuator assembly
    1. ECM (2AR-FE/2GR-FE/6AR-FSE)
    2. Power steering ECU with motor assembly
    3. Blind spot monitor sensor RH
    1. Airbag sensor assembly
    2. Rear television camera assembly
    3. Navigation receiver assembly
    4. Radio and display receiver assembly
    1. Vehicle Speed [ABS/VSC/TRC]
    2. Vehicle Speed (2AR-FE) [Engine and ECT]
    3. Vehicle Speed (2GR-FE/6AR-FSE) [Engine]
    4. Meter Vehicle Velocity [EMPS]
    5. Vehicle Speed Meter [Combination Meter]
    6. Vehicle Speed [Blind Spot Monitor Master]
    Combination meter assembly *3
    1. Clearance warning ECU assembly
    2. Smart key ECU assembly (Certification ECU)
    3. Multiplex tilt and telescopic ECU
    1. Air conditioning amplifier assembly
    2. Main body ECU (Multiplex network body ECU)
    3. Position control ECU and switch assembly (for Driver side)
    1. Vehicle Speed Meter [Combination Meter]
    2. Vehicle Speed Info [Clearance Sonar]
    3. Vehicle Speed Signal [Power Source Control]
    4. Freeze Speed Info [Tilt & Telescopic]
    Wheel speed
    Brake actuator assembly
    AFS ECU
    1. ECM (2AR-FE/2GR-FE/6AR-FSE)
    2. Power steering ECU with motor assembly
    3. Blind spot monitor sensor RH
    1. FR Wheel Speed [AFS]
    2. FL Wheel Speed [AFS]
    3. FR Wheel Speed [ABS/VSC/TRC]
    4. FL Wheel Speed [ABS/VSC/TRC]
    5. RR Wheel Speed [ABS/VSC/TRC]
    6. RL Wheel Speed [ABS/VSC/TRC]
    Shift position
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    1. Clearance warning ECU assembly
    2. Navigation receiver assembly
    3. Radio and display receiver assembly
    4. Smart key ECU assembly (Certification ECU)
    5. Brake actuator assembly
    6. Blind spot monitor sensor RH
    1. Airbag sensor assembly
    2. Combination meter assembly*2
    3. Main body ECU (multiplex network body ECU)
    4. AFS ECU
    5. Inner rear view mirror assembly
    6. Rear television camera assembly
    1. Neutral Position SW Signal (2AR-FE) [Engine and ECT]
    2. Neutral Position SW Signal (2GR-FE/6AR-FSE) [Engine]
    3. Parking Signal [Clearance Sonar]
    4. Reverse Signal [Clearance Sonar]
    5. Reverse Signal [Navigation System]
    6. Shift P Signal [Power Source Control]
    7. Shift Lever Position [ABS/VSC/TRC]
    8. Reverse [Blind Spot Monitor Master]
    Ambient temperature
    Air conditioning amplifier assembly
    1. ECM (2AR-FE/2GR-FE/6AR-FSE)
    2. Combination meter assembly
    1. Main body ECU (Multiplex network body ECU)
    2. Clearance warning ECU assembly
    1. Ambient Temp Sensor [Air Conditioner]
    2. Ambient Temp for A/C (2AR-FE) [Engine and ECT]
    3. Ambient Temp for A/C (2GR-FE/6AR-FSE) [Engine]
    4. Ambient Temperature [Combination Meter]
    FR door courtesy switch
    Main body ECU (Multiplex network body ECU)
    -
    1. Smart key ECU assembly (Certification ECU)
    2. Combination meter assembly *2
    FR Door Courtesy [Main Body]
    Steering angle sensor
    Steering sensor
    1. Power steering ECU with motor assembly
    2. Brake actuator assembly
    3. AFS ECU
    4. Blind spot monitor sensor RH
    1. Airbag sensor assembly
    2. Navigation receiver assembly
    3. Radio and display receiver assembly
    4. Rear television camera assembly
    1. Steering Angle Velocity [EMPS]
    2. Steering Angle Sensor [ABS/VSC/TRC]
    3. Steering Angle [Blind Spot Monitor Master]
    Yaw rate sensor
    Airbag sensor assembly
    Brake actuator assembly
    1. ECM (2AR-FE/2GR-FE/6AR-FSE)
    2. AFS ECU
    Yaw Rate Sensor [ABS/VSC/TRC]
    Deceleration sensor
    Airbag sensor assembly
    Brake actuator assembly
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    1. Deceleration Sensor [ABS/VSC/TRC]
    2. Deceleration Sensor2 [ABS/VSC/TRC]
    Headlight switch
    Main body ECU (Multiplex network body ECU)
    AFS ECU
    Combination meter assembly*2
    1. Headlight Low Beam State [AFS]
    2. Head Light SW (Head) [Main Body]
    Combination meter assembly power source voltage*1
    Combination meter assembly
    -
    -
    +B Voltage Value [Combination Meter]
    Power steering ECU with motor assembly power source voltage*1
    Power steering ECU with motor assembly
    -
    -
    IG Power Supply [EMPS]
    Solar sensor*1
    Air conditioning amplifier assembly
    -
    -
    Solar Sensor (D side) [Air Conditioner]
    Ignition switch condition*1
    Smart key ECU assembly (Certification ECU)
    -
    -
    Ignition Switch [Entry & Start]
    Clearance sonar main switch*1
    Clearance warning ECU assembly
    -
    -
    Main Switch [Clearance Sonar]
    ECM power source voltage*1
    ECM (2AR-FE/2GR-FE/6AR-FSE)
    -
    -
    1. Battery Voltage (2AR-FE) [Engine and ECT]
    2. Battery Voltage (2GR-FE/6AR-FSE) [Engine]
    AFS off switch condition*1
    AFS ECU
    -
    -
    AFS OFF Switch [AFS]
    Tilt up switch condition*1
    Multiplex tilt and telescopic ECU
    -
    -
    Tilt Up Switch [Tilt & Telescopic]
    Navigation receiver assembly power source voltage*1
    Navigation receiver assembly
    -
    -
    Battery Voltage [Navigation System]
    Radio and display receiver assembly*1
    Radio and display receiver assembly
    -
    -
    Battery Voltage [Navigation System]
    Blind spot monitor sensor RH power source voltage*1
    Blind spot monitor sensor RH
    -
    -
    Power Supply Voltage [Blind Spot Monitor Master]

    *1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
    *2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter.
    *3: The combination meter assembly receives a vehicle speed signal from the brake actuator assembly and sends the signal to other ECUs.

  2. Details of relevant Data List items (Selected system: Engine and ECT) (for 2AR-FE)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


    1. Warm up the engine.

    2. Turn the A/C switch off.

    3. Turn the ignition switch off.

    4. Connect the GTS to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine and ECT / Data List.

    8. Read the Data List according to the display on the GTS.

      Engine and ECT 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed
      Vehicle speed/
      Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Actual vehicle speed
      1. This is the current vehicle speed.
      2. The vehicle speed is detected using the wheel speed sensors.
        1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
      Engine Speed
      Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm
      610 to 710 rpm: Idling
      When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      Coolant Temp
      Coolant temperature/
      Min.: -40°C (-40°F), Max.: 140°C (284°F)
      75 to 100°C (167 to 212°F): After warming up
      This is the engine coolant temperature.

      HINT:
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      3. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
      4. Check if the engine overheats when the value indicates 140°C (284°F).

      Battery Voltage
      Battery voltage/
      Min.: 0 V, Max.: 65.535 V
      11 to 14 V: Idling
      If 11 V or less, characteristics of some electrical components may change.
      Accelerator Position
      Accelerator pedal position/
      Min.: 0%, Max.: 399.9%
      Actual accelerator pedal position
      This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%.
      Neutral Position SW Signal
      Park/neutral position switch status/
      ON or OFF
      ON: Shift lever in P or N
      -
      Ambient Temp for A/C
      Ambient temperature for A/C/
      Min.: -40°C (-40°F),
      Max.: 215°C (419°F)
      -
      -

  3. Details of relevant Data List items (Selected system: Engine) (for 2GR-FE)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    The actual values may differ from the values listed in the chart under "Results of real-vehicle check" due to climate, weather conditions, etc.

    HINT:
    Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


    1. Warm up the engine.

    2. Turn the A/C switch off.

    3. Turn the engine switch off.

    4. Connect the GTS to the DLC3.

    5. Turn the engine switch on (IG).

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine / Data List.

    8. Read the Data List according to the display on the GTS.

      Engine 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed
      Vehicle speed/
      Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Actual vehicle speed
      1. This is the current vehicle speed.
      2. The vehicle speed is detected using the wheel speed sensors.
        1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
        2. To accurately confirm whether the vehicle was stopped or not, use "SPD (NO)", which is the automatic transaxle output speed.
      Engine Speed
      Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm
      600 to 700 rpm: Idling
      When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      Coolant Temp
      Coolant temperature/
      Min.: -40°C (-40°F), Max.: 140°C (284°F)
      75 to 100°C (167 to 212°F): After warming up
      This is the engine coolant temperature.

      HINT:
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      3. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
      4. Check if the engine overheats when the value indicates 140°C (284°F).

      Battery Voltage
      Battery voltage/
      Min.: 0 V, Max.: 65.535 V
      11 to 14 V: Idling
      If 11 V or less, characteristics of some electrical components may change.
      Accelerator Position
      Accelerator pedal position/
      Min.: 0%, Max.: 399.9%
      Actual accelerator pedal position
      This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%.
      Neutral Position SW Signal
      Park/neutral position switch/
      ON or OFF
      ON: Shift lever in P or N
      -
      Ambient Temp for A/C
      Ambient temperature for A/C/
      Min.: -40°C (-40°F),
      Max.: 215°C (419°F)
      -
      -

  4. Details of relevant Data List items (Selected system: Engine) (for 6AR-FSE)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be off and all accessory switches should be off.


    1. Warm up the engine.

    2. Turn the A/C switch off.

    3. Turn the engine switch off.

    4. Connect the GTS to the DLC3.

    5. Turn the engine switch on (IG).

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Engine / Data List.

    8. Read the Data List according to the display on the GTS.

      Engine 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed
      Vehicle speed/
      Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Actual vehicle speed
      1. This is the current vehicle speed.
      2. The vehicle speed is detected using the wheel speed sensors.
        1. Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.
        2. To accurately confirm whether the vehicle was stopped or not, use "SPD (NO)", which is the automatic transaxle output speed.
      Engine Speed
      Engine speed/
      Min.: 0 rpm, Max.: 16383 rpm
      600 to 700 rpm: Idling
      When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.
      Coolant Temp
      Coolant temperature/
      Min.: -40°C (-40°F), Max.: 140°C (284°F)
      75 to 100°C (167 to 212°F): After warming up
      This is the engine coolant temperature.

      HINT:
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      3. If the value is -40°C (-40°F) or 140°C (284°F), the sensor circuit is open or shorted.
      4. Check if the engine overheats when the value indicates 140°C (284°F).

      Battery Voltage
      Battery voltage/
      Min.: 0 V, Max.: 65.5 V
      11 to 14 V: Idling
      If 11 V or less, characteristics of some electrical components may change.
      Accelerator Position
      Accelerator pedal position/
      Min.: 0%, Max.: 399.9%
      Actual accelerator pedal position
      This is the accelerator pedal position defined using the learned fully released position (sensor output) of accelerator pedal position sensor No. 1 as 0% and the fully depressed position as 100%.
      Neutral Position SW Signal
      Park/neutral position switch/
      ON or OFF
      ON: Shift lever in P or N
      -
      Ambient Temp for A/C
      Ambient temperature for A/C/
      Min.: -40°C (-40°F),
      Max.: 215°C (419°F)
      -
      -

  5. Details of relevant Data List items (Selected system: ABS/VSC/TRC)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    7. Read the Data List according to the display on the GTS.

      ABS/VSC/TRC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Deceleration Sensor
      Acceleration sensor reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
      -
      During deceleration/acceleration: Changes continuously
      Deceleration Sensor2
      Acceleration sensor 2 reading / Min.: -18.525 m/s2, Max.: 18.387 m/s2
      -
      During deceleration/acceleration: Changes continuously
      Yaw Rate Sensor
      Yaw rate sensor / Min.: -128 °/s, Max.: 127 °/s
      Vehicle stopped: 0 °/s
      Turning right: -128 to 0 °/s
      Turning left: 0 to 127 °/s
      -
      Steering Angle Sensor
      Steering angle sensor / Min.: -3276.8°, Max.: 3276.7°
      Turning left: Increase
      Turning right: Decrease
      -
      FR Wheel Speed
      Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      FL Wheel Speed
      Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RR Wheel Speed
      Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      RL Wheel Speed
      Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Shift Lever Position
      Shift lever position information / P,N, R, D/M, 1st-6th/B or Fail
      Actual shift lever position
      -
      Vehicle Speed
      Maximum wheel speed sensor reading / Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
      Vehicle stopped: 0 km/h (0 mph)
      When driving at constant speed: No large fluctuations
      Engine Revolutions
      Engine speed / Min.: 0 rpm, Max.: 65535 rpm
      Engine stopped: 0 rpm
      When engine speed is constant: No large fluctuations
      Accelerator Opening Angle %
      Percentage of accelerator pedal opening angle / Min.: 0.0%, Max.: 128.0%
      When the accelerator pedal is released: 0.0%
      During accelerator pedal operation: Changes in proportion with the pedal movement

  6. Details of relevant Data List items (Selected system: EMPS)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Turn the ignition switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / EMPS / Data List.

    6. Read the Data List according to the display on the GTS.

      EMPS 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Meter Vehicle Velocity
      Vehicle speed from meter/
      Min.: 0.0 km/h (0.0 mph)
      Max.: 300.0 km/h (186.4 mph)
      0 km/h (0 mph)
      Engine running and vehicle stopped
      No significant fluctuation
      Engine running and vehicle driven at constant speed
      Steering Angle Velocity
      Steering angle speed/
      Min.: -32768 deg/s
      Max.: 32767 deg/s
      Value changes in proportion to steering speed
      - The value increases when turning left and decreases when turning right
      Engine running and steering wheel being turned
      IG Power Supply
      IG power source voltage/
      Min.: 0.0000 V
      Max.: 20.1531 V
      9 to 16 V
      Ignition switch ON

  7. Details of relevant Data List items (Selected system: Navigation System)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Navigation System / Data List.

    5. Read the Data List according to the display on the GTS.

      Navigation System 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Battery Voltage
      Battery voltage/ Min.: 0 V, Max.:24 V
      11 to 14 V
      -
      Reverse Signal
      Reverse Signal/ON or OFF
      ON: Reverse selected
      OFF: Reverse not selected
      -

  8. Details of relevant Data List items (Selected system: Clearance Sonar)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the clearance sonar main switch on.

    4. Turn the GTS on.

    5. Enter the following menus: Body / Clearance Sonar / Data List.

    6. Read the Data List according to the display on the GTS.

      Clearance Sonar 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Main Switch
      Clearance sonar main switch/OFF or ON
      OFF: Clearance sonar main switch off
      ON: Clearance sonar main switch on
      -
      Parking Signal
      Parking signal/OFF or ON
      OFF: Shift lever in any position other than P
      ON: Shift lever in P
      -
      Reverse Signal
      Reverse signal/OFF or ON
      OFF: Shift lever in any position other than R
      ON: Shift lever in R
      -
      Vehicle Speed Info
      Vehicle speed signal/Snr Stop or Snr Work
      Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating)
      Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9 km/h (5.6 mph) (when decelerating)
      -

  9. Details of relevant Data List items (Selected system: Entry & Start)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    1. Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
    2. When using the GTS with the ignition switch off to troubleshoot:
      Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Entry & Start / Data List.

    5. Read the Data List according to the display on the GTS.

      Entry & Start 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Ignition Switch
      Engine switch ON / ON or OFF
      ON: Engine switch ON
      OFF: Engine switch off
      1. Displays whether the IG power source signal input is on or off.
      2. Use this Data List item to help determine the cause when all smart entry and start system/wireless functions do not operate.
      3. If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal, the engine switch will turn ON. At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the smart key ECU assembly (certification ECU) are compared, and the L code stored in the smart key ECU assembly (certification ECU) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered ON at that time.*1
      4. If the electrical key transmitter sub-assembly is brought inside the vehicle and the engine switch is pressed twice without depressing the brake pedal, the engine switch will turn ON. At this time, the key ID code transmitted from the electrical key transmitter sub-assembly and the key ID code stored in the smart key ECU assembly (certification ECU) are compared, and the S code stored in the smart key ECU assembly (certification ECU) and the code stored in the steering lock ECU (steering lock actuator assembly) are compared, and if all codes match, the power source mode is considered ON at that time.*2
      *1: w/ Wireless Door Lock Buzzer Answer Back Function
      *2: w/o Wireless Door Lock Buzzer Answer Back Function

  10. Details of relevant Data List items (Selected system: Power Source Control)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Power Source Control / Data List.

    5. Read the Data List according to the display on the GTS.

      Power Source Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Shift P Signal
      Shift position P/ON or OFF
      ON: Shift lever in P
      OFF: Shift lever not in P
      1. Use this item to determine if the shift position switch is malfunctioning.
      2. The engine cannot be started when this item is "OFF".
      Vehicle Speed Signal
      Vehicle being driven or stopped/Stop or Run
      Stop: Vehicle stopped
      Run: Vehicle being driven at 5 km/h (3 mph) or more
      -

  11. Details of relevant Data List items (Selected system: Starting Control)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Starting Control / Data List.

    5. Read the Data List according to the display on the GTS.

      Starting Control 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Engine Speed
      Engine speed/0 to 16383 r/min
      Fluctuates in accordance with engine speed
      -

  12. Details of relevant Data List items (Selected system: Combination Meter)
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the ignition switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the ignition switch to ON.

    5. Turn the GTS on.

    6. Enter the following menus: Body / Combination Meter / Data List.

    7. Read the Data List according to the display on the GTS.

      Combination Meter 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Vehicle Speed Meter
      Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
      Almost the same as actual vehicle speed
      -
      Engine Rpm
      Engine speed/Min.: 0 rpm, Max.: 12750 rpm
      1. 600 to 700 rpm: Idling (2GR-FE)
      2. 610 to 710 rpm: Idling (2AR-FE)
      -
      Coolant Temperature
      Engine coolant temperature/-40 to 127.5°C (-40 to 261.5°F)
      After warming up: 75 to 100°C (167 to 212°F)

      HINT:
      1. After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).
      2. After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.
      3. If the value is -40°C (-40°F), or higher than 135°C (275°F), the sensor circuit is open or shorted.
      4. Check if the engine overheats when the value indicates higher than 135°C (275°F).

      +B Voltage Value
      Battery voltage/Min.: 0 V, Max.: 25.5 V
      11 to 14 V
      -
      Ambient Temperature
      Outside temperature/Min.: -40°C (-40°F), Max.: 87.5°C (189.5°F)
      Almost the same as actual outside temperature
      The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

  13. Details of relevant Data List items (Selected system: Air Conditioner)
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Air Conditioner / Data List.

    5. Read the Data List according to the display on the GTS.

      Air Conditioner 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Ambient Temp Sensor
      Ambient temperature sensor (thermistor assembly) /
      Min.: -23.30°C (-9.94°F)
      Max.: 65.95°C (150.71°F)
      Actual ambient temperature displayed
      -
      Solar Sensor (D side)
      Driver side automatic light control sensor (solar sensor) /
      Min.: 0
      Max.: 255
      Driver side automatic light control sensor (solar sensor) value increases as brightness increases
      -
      Engine Coolant Temp
      Engine coolant temperature sensor /
      Min.: 1.30°C (34.34°F)
      Max.: 90.55°C (194.99°F)
      Actual engine coolant temperature displayed
      -

  14. Details of relevant Data List items (Selected system: Main Body ECU) (Multiplex Network Body ECU)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      FR Door Courtesy
      Front door courtesy light switch RH signal / ON or OFF
      ON: Front door RH closed
      OFF: Front door RH open
      -

  15. Details of relevant Data List items (Selected system: Tilt & Telescopic)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / Tilt & Telescopic / Data List.

    5. Read the Data List according to the display on the GTS.

      Tilt & Telescopic 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Freeze Speed Info
      Vehicle speed data/
      Min.: 0 km/h (0 mph)
      Max.: 255 km/h (158 mph)
      Stop → Drive → Stop
      0 km/h (0 mph) → Same speed as indicated on speedometer → 0 km/h (0 mph)

  16. Details of relevant Data List items (Selected system: AFS)

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body / AFS / Data List.

    5. Read the Data List according to the display on the GTS.

      AFS 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Headlight Low Beam State
      Low beam headlight state/ON or OFF
      ON: Low beam headlights on
      OFF: Low beam headlights off
      -
      Steering Sens Signal
      Steering angle sensor signal value/-384.0 deg to 382.5 deg
      Approx. 0 deg (When steering wheel is straight)
      Value changes according to steering wheel position
      FR Wheel Speed
      Front right wheel speed/0.00 to 327.67 km/h (203.61 mph)
      Condition can be displayed
      -
      FL Wheel Speed
      Front left wheel speed/0.00 to 327.67 km/h (203.61 mph)
      Condition can be displayed
      -
      Vehicle Speed
      Vehicle speed/0.00 to 327.67 km/h (203.61 mph)
      Condition can be displayed
      -

  17. Details of relevant Data List items (Selected system: Blind Spot Monitor Master)

    NOTICE:
    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    HINT:
    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.

    5. According to the display on the GTS, read the Data List.

      Blind Spot Monitor Master  
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Reverse (Only for AT/CVT)
      State of the Shift Position R Signal / OFF or ON
      ON: Shift lever in R
      OFF: Shift lever in any position other than R
      -
      Vehicle Speed
      Vehicle speed signal / Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph)
      Vehicle stopped: 0 km/h (0 mph)
      -
      Steering Angle
      Steering angle sensor / Min.: -3072°, Max.: 3070.5°
      Left turn: Increase
      Right turn: Decrease
      -
      Power Supply Voltage
      Power supply voltage / Min.: 0 V, Max.: 50 V
      Always: 11 to 14 V
      -