Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/o Occupant Classification System)

SEAT BELT WARNING SYSTEM (w/o Occupant Classification System) > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

The occupant detection sensor (separate type front seat cushion pad) detects if the passenger seat is occupied and sends signals to the combination meter assembly. The front seat inner belt assembly RH detects the passenger seat belt condition and sends signals to the combination meter assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly RH, the seat belt warning light in the combination meter assembly will blink or go off.

HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM


B271142E04


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Combination Meter (Combination Meter Assembly) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Seatbelt Buckle SW
    Front passenger seat belt buckle switch signal/ON or OFF
    ON: Front passenger seat belt unfastened
    OFF: Front passenger seat belt fastened
    -

    OK:
    ON or OFF appears on the tester screen according to the front passenger seat belt condition.



NG
Go to step 2
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY RH - BODY GROUND)
  1. Disconnect the I18 combination meter assembly connector.

  1. Disconnect the O3 front seat inner belt assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I18-20 (P/SB) - O3-3
    Always
    Below 1 Ω
    I18-20 (P/SB) - Body ground
    Always
    10 kΩ or higher
    O3-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)


    B218574E01
  1. Remove the occupant detection sensor (separate type front seat cushion pad) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 3
    Front passenger seat occupied
    Below 100 Ω
    1 - 3
    Front passenger seat not occupied
    1 MΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Occupant Detection Sensor (Separate Type Front Seat Cushion Pad))



NG
REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD) (Click here)
OK


4.INSPECT FRONT SEAT INNER BELT ASSEMBLY RH


    B271152E06
  1. Remove the front seat inner belt assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    O3-3 - B-1
    Always
    Below 1 Ω
    O3-2 - B-3
    Front passenger seat belt unfastened
    Below 1 Ω
    O3-2 - B-3
    Front passenger seat belt fastened
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Front Seat Inner Belt Assembly RH)



NG
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)