RADIATOR > INSTALLATION |
| 1. INSTALL RADIATOR ASSEMBLY |
![]() |
Install the fan assembly to the radiator with the 2 guides at the bottom and 3 claws on the top.
| *1 | Guide |
Install the 2 lower radiator supports to the radiator assembly.
![]() |
Install the radiator with fan assembly.
Install the condenser assembly with the 4 bolts.
Connect the 3 clamps and connector.
| 2. INSTALL UPPER RADIATOR SUPPORT |
Install the 2 radiator support cushions to the radiator assembly.
Install the upper radiator support with the 5 bolts and connect the hood lock control cable clamp to the upper radiator support.
Connect the 2 connectors.
| 3. INSTALL HOOD LOCK ASSEMBLY (for LHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 4. INSTALL HOOD LOCK ASSEMBLY (for RHD) |
![]() |
Apply MP grease to the sliding areas of the lock.
Connect the hood lock control cable assembly.
Install the hood lock assembly with the 2 bolts and hood lock bolt.
Connect the connector.
| 5. CONNECT OUTLET NO. 1 OIL COOLER HOSE |
Connect the outlet No. 1 oil cooler hose.
| 6. CONNECT INLET NO. 1 OIL COOLER HOSE |
Connect the inlet No. 1 oil cooler hose.
| 7. CONNECT NO. 2 RADIATOR HOSE |
Connect the No. 2 radiator hose and clamp.
| 8. CONNECT NO. 1 RADIATOR HOSE |
Connect the No. 1 radiator hose.
| 9. INSTALL RADIATOR RESERVE TANK ASSEMBLY |
Install the radiator reserve tank with the 2 bolts.
Connect the radiator reserve tank hose.
| 10. INSTALL INLET NO. 1 AIR CLEANER |
![]() |
Install the inlet No. 1 air cleaner to the intake air resonator sub-assembly.
Engage the pin to the radiator support.
| 11. INSTALL INLET NO. 2 AIR CLEANER |
Install the inlet No. 2 air cleaner to the air cleaner case sub-assembly with the 2 bolts.
Connect the 2 wire harness clamps and vacuum hose clamp.
| 12. INSTALL FRONT BUMPER ASSEMBLY |
| 13. INSTALL BATTERY |
Install the battery and battery tray.
Install the battery clamp with the bolt and nut.
Connect the positive (+) cable to the positive (+) battery terminal.
| 14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 15. ADD ENGINE COOLANT |
Tighten the radiator drain cock plug by hand.
Close the cylinder block drain cock plug (for Bank 1).
Close the cylinder block drain cock plug (for Bank 2, w/ Cylinder Block Drain Cock Plug).
Loosen the air drain cock plug on the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until engine coolant overflows from the air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
![]() |
Slowly fill the radiator assembly with TOYOTA Super Long Life Coolant (SLLC).
| *a | Code Mark |
| Code Mark "K" | 8.8 liters (9.3 US qts, 7.7 Imp. qts) |
| Code Mark "J" | 8.9 liters (9.4 US qts, 7.8 Imp. qts) |
Remove the reserve tank cap.
Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the engine coolant.
If the engine coolant level is low, add engine coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the engine coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 16. INSPECT FOR COOLANT LEAK |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 17. INSTALL ENGINE UNDER COVER LH |
| 18. INSTALL ENGINE UNDER COVER RH |
| 19. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH |
| 20. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH |