Home › Engine / Hybrid System ยท 2AR-FE › COOLING › RADIATOR

RADIATOR > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).



2. DRAIN ENGINE COOLANT

NOTICE:
Do not remove the radiator cap sub-assembly or radiator drain cock plug while the engine and radiator assembly are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A315230E01
  1. Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock as shown in the illustration.
    Text in Illustration 
    *1
    Engine Under Cover LH
    *a
    Hose

  1. Loosen the radiator drain cock plug.



    A338632E01
  1. Remove the radiator cap sub-assembly. Then drain the engine coolant.
    Text in Illustration 
    *1
    Radiator Cap Sub-assembly
    *2
    Radiator Drain Cock Plug

    HINT:
    Collect the engine coolant in a container and dispose of it according to the regulations in your area.

  1. Disconnect the hose from the radiator drain cock.



3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH


4. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH


5. REMOVE ENGINE UNDER COVER RH


6. REMOVE ENGINE UNDER COVER LH


7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



8. REMOVE FRONT BUMPER ASSEMBLY
(Click here)


9. REMOVE INLET AIR CLEANER ASSEMBLY


    A255404
  1. Remove the 2 bolts and inlet air cleaner assembly.



10. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    A348527E01
  1. Disconnect the radiator reserve tank hose.
    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made

  1. Remove the 2 bolts and radiator reserve tank assembly.



11. DISCONNECT NO. 1 RADIATOR HOSE


    A255302
  1. Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.



12. DISCONNECT NO. 2 RADIATOR HOSE


    A255304
  1. Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.

  1. Disengage the clamp and disconnect the No. 2 radiator hose from the fan assembly.



13. DISCONNECT INLET NO. 1 OIL COOLER HOSE (w/ Oil Cooler)


    A255889
  1. Slide the clip and disconnect the inlet No. 1 oil cooler hose.



14. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (w/ Oil Cooler)


    A255890
  1. Slide the clip and disconnect the outlet No. 1 oil cooler hose.



15. REMOVE HOOD LOCK ASSEMBLY (for TMC, TMMR Made)
for LHD: Click here
for RHD: Click here


16. REMOVE HOOD LOCK ASSEMBLY (for TMMK Made)


    B382415E01
  1. Using a screwdriver, remove the hood lock nut cap.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



  1. w/ Engine Hood Courtesy Switch:



      B381594
    1. Disconnect the connector.



    B380676E01
  1. Remove the 2 bolts and hood lock bolt.
    Text in Illustration 
    *1
    Hood Lock Bolt



    B380677
  1. Disconnect the hood lock control cable assembly and remove the hood lock assembly.



17. REMOVE UPPER RADIATOR SUPPORT


    A263146
  1. Disconnect the 2 horn connectors.



    A264524E02
  1. Disengage the clamp and disconnect the hood lock control cable assembly from the upper radiator support.
    Text in Illustration 
    *A
    for RHD
    *B
    for LHD

  1. Remove the 5 bolts and upper radiator support.

  1. Remove the 2 radiator support cushions from the radiator assembly.



18. REMOVE RADIATOR ASSEMBLY


    A348522E01
  1. Disconnect the cooling fan motor connector and No. 2 cooling fan motor connector.
    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made

  1. Disengage the 2 clamps.



    A259413
  1. Remove the 4 bolts and separate the condenser assembly from the radiator assembly.



    A348299
  1. Remove the radiator assembly with the fan assembly from the vehicle.

    NOTICE:
    Do not apply any excessive force to the condenser assembly or pipe when removing the radiator assembly.

  1. Remove the 2 lower radiator supports from the radiator assembly.



    A348663E01
  1. Disengage the 3 claws.
    Text in Illustration 
    *A
    for TMC, TMMR Made
    *B
    for TMMK Made

  1. Disengage the 2 guides and remove the fan assembly from the radiator assembly.

    NOTICE:
    Do not damage the radiator assembly when removing the fan assembly.