Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C146C    Open in ABS Motor Relay Circuit

for Preparation Click here


DESCRIPTION

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the skid control ECU turns the ABS motor relay on to operate the pump motor.
If the voltage supplied to the ABS motor relay (+BM) is too low due to low voltage from the battery or alternator, the DTC may be stored.

DTC No.
DTC Detection Condition
Trouble Area
C146C
Any of the following is detected:
  1. When the ABS motor relay is actuated, voltage is not supplied to the pump motor.
  2. When the ABS motor relay is not actuated, voltage in the pump motor is high.
  3. The skid control ECU judges that pump motor operation is abnormal.
  1. ABS NO. 1 fuse (Fusible link block assembly)
  2. ABS motor relay circuit
  3. ABS motor relay (Brake actuator assembly)

WIRING DIAGRAM


C250530E03


INSPECTION PROCEDURE

HINT:
When C1241 and/or C1417 is output together with C146C, inspect and repair the trouble areas indicated by C1241 and/or C1417 first (Click here, and/or Click here).

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test using the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay ON/OFF
    Operating sound of motor can be heard

  1. Check the operating sound of the pump motor when operating it using the intelligent tester.

    Result:

    Result
    Proceed to
    Operating sound is heard.
    A
    Operating sound is not heard.
    B



B
Go to step 3
A


2.RECONFIRM DTC

HINT:
This DTC is stored when a problem is identified in the brake actuator assembly.
The ABS motor relay is in the brake actuator assembly.
Therefore, motor relay inspection and motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 40 km/h (25 mph) or more for 30 seconds or more.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C146C is not output.
    A
    DTC C146C is output.
    B

    HINT:
    1. If a speed signal of 40 km/h (25 mph) or more is received by the skid control ECU with the ignition switch ON, the skid control ECU performs self diagnosis of the motor circuit.
    2. If the normal system code is output (No DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly.
    3. If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.
    4. If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)


    C238832E14
  1. Check that the ABS NO. 1 (50 A) fuse is normal.

    HINT:
    If the result is not as specified, replace the ABS NO. 1 fuse (fusible link block assembly).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A49-1 (+BM) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)


    C238832E15
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A49-13 (GND2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)