Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1411/11    Room Temperature Sensor Circuit

for Preparation Click here


DESCRIPTION

The room temperature sensor (cooler thermistor) is installed in the instrument panel to detect the cabin temperature which is used to control the heater and air conditioning system AUTO mode. The resistance of the room temperature sensor (cooler thermistor) changes in accordance with the cabin temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies a voltage (5 V) to the room temperature sensor (cooler thermistor) and reads voltage changes due to changes in the resistance of the room temperature sensor (cooler thermistor).

DTC No.
DTC Detection Condition
Trouble Area
B1411/11
Open or short in room temperature sensor (cooler thermistor) circuit
  1. Room temperature sensor (cooler thermistor)
  2. Harness or connector between room temperature sensor (cooler thermistor) and air conditioning amplifier assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E236721E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Room Temperature Sensor
    Room temperature sensor (cooler thermistor) /
    min.: -6.50°C (20.30°F)
    max.: 57.25°C (135.05°F)
    Actual cabin temperature displayed
    -

    OK:
    The display is as specified in the normal condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC (for TMC, TMMR Made))
    C
    OK (When troubleshooting according to the DTC (for TMMK Made))
    D



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

D
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.INSPECT ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)
  1. Remove the room temperature sensor (cooler thermistor) (Click here(for TMC, TMMR Made)) (Click here (for TMMK Made)).



    E161677E45
  1. Disconnect the I57 room temperature sensor (cooler thermistor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I57-1 (+) - I57-2 (-)
    10°C (50°F)
    3.00 to 3.73 kΩ
    I57-1 (+) - I57-2 (-)
    15°C (59°F)
    2.45 to 2.88 kΩ
    I57-1 (+) - I57-2 (-)
    20°C (68°F)
    1.95 to 2.30 kΩ
    I57-1 (+) - I57-2 (-)
    25°C (77°F)
    1.60 to 1.80 kΩ
    I57-1 (+) - I57-2 (-)
    30°C (86°F)
    1.28 to 1.47 kΩ
    I57-1 (+) - I57-2 (-)
    35°C (95°F)
    1.00 to 1.22 kΩ
    I57-1 (+) - I57-2 (-)
    40°C (104°F)
    0.80 to 1.00 kΩ
    I57-1 (+) - I57-2 (-)
    45°C (113°F)
    0.65 to 0.85 kΩ
    I57-1 (+) - I57-2 (-)
    50°C (122°F)
    0.50 to 0.70 kΩ
    I57-1 (+) - I57-2 (-)
    55°C (131°F)
    0.44 to 0.60 kΩ
    I57-1 (+) - I57-2 (-)
    60°C (140°F)
    0.36 to 0.50 kΩ

    NOTICE:
    1. Hold the sensor only by its connector. Touching the sensor may change the resistance value.
    2. When measuring, the sensor temperature must be the same as the ambient temperature.

    HINT:
    As the temperature increases, the resistance decreases (see the graph).

    Text in Illustration 
    *a
    Component without harness connected
    (Room Temperature Sensor (Cooler Thermistor))
    *b
    Sensing Portion
    *c
    Resistance (kΩ)
    *d
    Allowable Range
    *e
    Temperature (°C (°F))

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMC, TMMR Made)
    B
    NG (for TMMK Made)
    C



B
REPLACE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR) (Click here)

C
REPLACE ROOM TEMPERATURE SENSOR (COOLER THERMISTOR) (Click here)
A


3.CHECK HARNESS AND CONNECTOR ( ROOM TEMPERATURE SENSOR (COOLER THERMISTOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
  1. Disconnect the I77 air conditioning amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I77-29 (TR) - I57-1 (+)
    Always
    Below 1 Ω
    I77-34 (SG-1) - I57-2 (-)
    Always
    Below 1 Ω
    I77-29 (TR) - Body ground
    Always
    10 kΩ or higher
    I77-34 (SG-1) - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    OK (for TMC, TMMR Made)
    A
    OK (for TMMK Made)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)