SFI SYSTEM > VC Output Circuit |



| 1.CHECK MIL |
Check that the Malfunction Indicator Lamp (MIL) lights up when the engine switch is turned on (IG).
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Check the communication between the tester and ECM.
| Result | Proceed to |
| Communication is not possible | A |
| Communication is possible | B |
|
| ||||
| A | |
| 3.CHECK MIL (THROTTLE POSITION SENSOR) |
Disconnect the throttle with motor body assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY) |
Disconnect the accelerator pedal sensor assembly connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 5.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 1)) |
Disconnect the VVT sensor (for intake camshaft of bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 6.CHECK MIL (VVT SENSOR (FOR INTAKE CAMSHAFT OF BANK 2)) |
Disconnect the VVT sensor (for intake camshaft of bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 7.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 1)) |
Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 8.CHECK MIL (VVT SENSOR (FOR EXHAUST CAMSHAFT OF BANK 2)) |
Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.
Turn the engine switch on (IG).
Check the MIL.
| Result | Proceed to |
| MIL does not illuminate | A |
| MIL illuminates | B |
|
| ||||
| A | |
| 9.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle with motor body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E16-5 (VC) or E26-126 (VCTA) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM) |
Disconnect the accelerator pedal sensor assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-4 (VCPA) or A25-56 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A36-1 (VCP2) or A25-59 (VCP2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (VCV1 CIRCUIT) |
Disconnect the VVT sensor (for intake camshaft of bank 1) connector.
Disconnect the VVT sensor (for intake camshaft of bank 2) connector.
Disconnect the VVT sensor (for exhaust camshaft of bank 1) connector.
Disconnect the VVT sensor (for exhaust camshaft of bank 2) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E26-111 (VCV1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||