DTC B1850/62 Short in Rear Side Squib RH Circuit |
DTC B1851/62 Open in Rear Side Squib RH Circuit |
DTC B1852/62 Short to GND in Rear Side Squib RH Circuit |
DTC B1853/62 Short to B+ in Rear Side Squib RH Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1850/62 |
|
|
| B1851/62 |
| |
| B1852/62 |
| |
| B1853/62 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the rear seat airbag assembly RH and airbag sensor assembly.
Disconnect the connectors from the rear seat airbag assembly RH and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
|
| ||||
| OK | |
| 2.CHECK REAR SEAT AIRBAG ASSEMBLY RH (REAR SIDE SQUIB RH) |
![]() |
Connect the connector to the airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Rear Seat Airbag Assembly RH) |
|
| ||||
| OK | ||
| ||
| 3.CHECK NO. 2 FLOOR WIRE |
![]() |
Disconnect the No. 2 floor wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz2-1 (SRR+) - Body ground | Engine switch on (IG) | Below 1 V |
| Oz2-2 (SRR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz2-1 (SRR+) - Oz2-2 (SRR-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz2-1 (SRR+) - Body ground | Always | 1 MΩ or higher |
| Oz2-2 (SRR-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz2-1 (SRR+) - Oz2-2 (SRR-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Rear Seat Airbag Assembly RH) |
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the rear seat airbag assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Rear Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||