DTC B1820/55 Short in Side Squib RH Circuit |
DTC B1821/55 Open in Side Squib RH Circuit |
DTC B1822/55 Short to GND in Side Squib RH Circuit |
DTC B1823/55 Short to B+ in Side Squib RH Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| B1820/55 |
|
|
| B1821/55 |
| |
| B1822/55 |
| |
| B1823/55 |
|

| 1.CHECK CONNECTORS |
![]() |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check that the connectors are properly connected to the front seat airbag assembly RH and airbag sensor assembly.
Disconnect the connectors from the front seat airbag assembly RH and airbag sensor assembly.
Check that the terminals of the connectors are not damaged.
Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.
| *1 | Front Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
|
| ||||
| OK | |
| 2.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (FRONT SIDE SQUIB RH) |
![]() |
Connect the connector to the airbag sensor assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Disconnect SST from connector C.
| *1 | Front Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *a | Front view of wire harness connector (to Front Seat Airbag Assembly RH) |
|
| ||||
| OK | ||
| ||
| 3.CHECK NO. 2 FLOOR WIRE |
![]() |
Disconnect the No. 2 floor wire from the airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz1-1 (SFR+) - Body ground | Engine switch on (IG) | Below 1 V |
| Oz1-2 (SFR-) - Body ground | Engine switch on (IG) | Below 1 V |
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal.
Check for an open in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz1-1 (SFR+) - Oz1-2 (SFR-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz1-1 (SFR+) - Body ground | Always | 1 MΩ or higher |
| Oz1-2 (SFR-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Oz1-1 (SFR+) - Oz1-2 (SFR-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to the original condition.
| *1 | Front Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
| *3 | No. 2 Floor Wire |
| *a | Front view of wire harness connector (to Front Seat Airbag Assembly RH) |
|
| ||||
| OK | |
| 4.CHECK DTC |
![]() |
Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory (Click here).
Turn the engine switch off.
Turn the engine switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Seat Airbag Assembly RH |
| *2 | Airbag Sensor Assembly |
|
| ||||
| OK | ||
| ||