Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM

KEY REMINDER WARNING SYSTEM > Key Reminder Buzzer does not Sound

for Preparation Click here


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM


B281179E02


INSPECTION PROCEDURE

NOTICE:
Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the How to Proceed with Troubleshooting procedure (Click here). Then, conduct the following inspection procedure.

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
  1. Check the seat belt warning buzzer operation (Click here).

    HINT:
    The key reminder warning system sounds the buzzer built into the combination meter assembly as a key reminder warning. This buzzer is also used for the seat belt warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the seat belt is not fastened.

    OK:
    Combination meter buzzer sounds.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


2.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Select FL Door Courtesy in the Data List and read the intelligent tester display.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FL Door Courtesy
    Front door courtesy light switch LH signal/ON or OFF
    ON: Front door LH closed
    OFF: Front door LH open
    -

    OK:
    ON or OFF appears on the screen according to the driver door condition.



NG
Go to step 4
OK


3.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH ASSEMBLY)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Select Key Unlock Warning SW in the Data List and read the intelligent tester display.

    Main Body (Main Body ECU (Multiplex Network Body ECU)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal/ON or OFF
    ON: Key in ignition key cylinder
    OFF: No key in ignition key cylinder
    -

    OK:
    ON or OFF appears on the screen according to whether the key is in the ignition key cylinder.



NG
Go to step 7
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

4.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR)
  1. Remove the front door courtesy light switch assembly (for driver door) (for TMMK Made) (Click here).



    B203492E11
  1. Remove the front door courtesy light switch assembly (for driver door) (for TMC, TMMR Made) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Switch body
    Courtesy switch pushed (Door closed)
    10 kΩ or higher
    1 - Switch body
    Courtesy switch free (Door open)
    Below 1 Ω

    Text in Illustration 
    *1
    Switch Body
    *a
    Component without harness connected
    (Front Door Courtesy Light Switch Assembly (for driver door ))

    Result:
    Result
    Proceed to
    OK
    A
    NG (for TMMK Made)
    B
    NG (for TMC, TMMR Made)
    C



B
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR) (Click here)

C
REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (for DRIVER DOOR) (Click here)
A


5.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
  1. Disconnect the 3C instrument panel junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N7-1 - 3C-15
    Always
    Below 1 Ω
    N7-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
  1. Remove the instrument panel junction block assembly (Click here).


E173023E12

  1. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3C-15 - MB-2 (FLCY)
    Always
    Below 1 Ω


    Text in Illustration 
    *a
    Component without harness connected
    (Instrument Panel Junction Block Assembly)
    -
    -



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

7.INSPECT UNLOCK WARNING SWITCH ASSEMBLY


    B203483E05
  1. Remove the unlock warning switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch free (Key removed)
    10 kΩ or higher
    1 - 2
    Switch pushed (Key set)
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Unlock Warning Switch Assembly)



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
  1. Disconnect the I13 main body ECU (multiplex network body ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I33-1 - I13-17 (KSW)
    Always
    Below 1 Ω
    I33-2 - Body ground
    Always
    Below 1 Ω
    I33-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)