Home › Steering › STEERING COLUMN › STEERING LOCK SYSTEM

STEERING LOCK SYSTEM > Unable to Unlock Steering Wheel (Engine cannot Start)

for Preparation Click here


DESCRIPTION

The steering lock actuator assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if an engine start operation is performed while shaking the steering wheel in the same manner as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly), ID code box (immobiliser code ECU) (for vehicles with entry function on driver door except TMMK made) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.

Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Unable to unlock steering wheel (Engine cannot start)
Entry&Start
  1. All items (Click here)
-

WIRING DIAGRAM


C313934E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
  2. Perform either of the following operations to lock/unlock the steering:
    1. To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
    2. To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
  3. The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (Click here).
  4. After performing repairs, confirm that the problem does not occur.
  5. Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
  6. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  7. When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) (for vehicles with entry function on driver door except TMMK made), registration must be performed (refer to Service Bulletin).
  8. When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).
  9. If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch. This prevents the engine from starting while the steering is locked.

1.CHECK DTC (ALL)
  1. Using the intelligent tester, confirm the output of DTCs for all systems.

    OK:
    No DTCs are output.

    NOTICE:
    1. When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
    2. Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart (Click here).



NG
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
OK


2.CHECK ENGINE SWITCH (SWITCH CONDITION)
  1. Check the power source mode change.

    1. When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:

      OK:
      Off → on (ACC) → on (IG) → off



NG
GO TO SMART ENTRY AND START SYSTEM (for Start Function) (PROBLEM SYMPTOMS TABLE) (Click here)
OK


3.READ VALUE USING INTELLIGENT TESTER (UNLOCK REQUEST RECEIVE)
  1. Use the Data List to check if the steering lock request is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Unlock Request Receive*1
    Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
    NG: Except above
    1. If the unlock signal has not been received, the engine cannot be started.
    2. If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    Unlock Request Receive*2
    Reception state of steering unlock request signal by certification ECU (smart key ECU assembly) / OK or NG

    HINT:
    1. The reception state is maintained for 10 seconds.
    2. When 10 seconds or more elapse after receiving the signal, the item changes to "NG".

    OK: Within 10 seconds of turning engine switch on (IG) or on (ACC) or starting engine
    NG: Except above
    1. If the unlock signal has not been received, the engine cannot be started.
    2. If this item does not change to "OK" even though the steering unlock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning.
    *1: w/ entry function on driver door except TMMK made
    *2: w/o entry function on driver door for TMMK made

    OK:
    Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".


    Result:

    Result
    Proceed to
    OK
    A
    NG (w/o entry function on driver door for TMMK made)
    B
    NG (w/ entry function on driver door except TMMK made)
    C



B
Go to step 9

C
Go to step 12
A


4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


  1. Measure the voltage according to the value(s) in the table below.


    B264896E37


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    -
    -

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I78-25 (P) - A43-11 (E)
    Shift lever in P
    9 V or higher
    I78-25 (P) - A43-11 (E)
    Shift lever not in P
    1.5 V or less



NG
Go to step 7
OK


5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
  1. Disconnect the I24 steering lock ECU connector.



    C157850E41
  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I24-1 (GND) - Body ground
    Always
    Below 1 Ω

    NOTICE:
    If the result is not as specified, check for looseness in the connection which leads to ground.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I24-7 (B) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Steering Lock ECU (Steering Lock Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT STEERING LOCK ECU (MOTOR ACTIVATION COMMAND SIGNAL)
  1. Reconnect the I24 steering lock ECU connector.



    C241547E02
  1. Check the signal waveform according to the condition(s) in the table below.
    Standard Frequency 
    Item
    Content
    Tester Connection
    I24-3 (IGE) - I24-1 (GND)
    Tool Setting
    2 V/DIV., 200 ms./DIV.
    Vehicle Condition
    Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating
    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU (Steering Lock Actuator Assembly))
    *b
    Steering lock motor not operating
    *c
    Steering lock motor operating

HINT:
  1. When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
  2. In order to take measurements when the lock motor is operating, perform either of the following operations:
    1. To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG) with the shift lever in P.
    2. To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
  1. Disconnect the I42 shift lock control ECU (lower shift lever assembly) connector.

  1. Disconnect the I78 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I42-3 (P2) - I78-25 (P)
    Always
    Below 1 Ω
    I42-3 (P2) - Body ground
    Always
    10 kΩ higher
    I78-25 (P) - Body ground
    Always
    10 kΩ higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT SHIFT LOCK CONTROL ECU (LOWER SHIFT LEVER ASSEMBLY)
  1. Reconnect the I42 shift lock control ECU (lower shift lever assembly) connector.



    C305098E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I42-3 (P2) - Body ground
    Shift lever in P
    9 V or higher
    I42-3 (P2) - Body ground
    Shift lever not in P
    1.5 V or less

    Text in Illustration 
    *a
    Component with harness connected
    (Shift Lock Control ECU (Lower Shift Lever Assembly))

    Result:
    Result
    Proceed to
    OK
    A
    NG (for U660E)
    B
    NG (for U760E) (for TMMK Made)
    C
    NG (for U760E) (for TMC, TMMR Made)
    D
    NG (for U761E)
    E



B
GO TO SHIFT LEVER (INSPECTION) (Click here)

C
GO TO SHIFT LEVER (INSPECTION) (Click here)

D
GO TO SHIFT LEVER (INSPECTION) (Click here)

E
GO TO SHIFT LEVER (INSPECTION) (Click here)
A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)  

Go to step 11

9.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Use the Data List to check if L code certification is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.

    HINT:
    Reasons for verification failure:
    1. The steering lock ECU or certification ECU (smart key ECU assembly) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 11
OK


10.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).

  1. Perform registration (refer to Service Bulletin).

  1. Turn the engine switch on (IG).

  1. Turn the steering wheel and check the steering condition.

    OK:
    Steering is unlocked.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END 

11.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

  1. Perform registration (refer to Service Bulletin).

  1. Use the Data List to check if L code certification is functioning properly again.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between certification ECU (smart key ECU assembly) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or steering lock ECU is not registered or the certification ECU (smart key ECU assembly) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.



NG
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (Click here)
OK

END 

12.READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
  1. Use the Data List to check if S code certification is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Check
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.

    HINT:
    Reasons for verification failure:
    1. The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 15
OK


13.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Use the Data List to check if L code certification is functioning properly.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the ID code box (immobiliser code ECU) or steering lock ECU is not registered or the ID code box (immobiliser code ECU) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.

    HINT:
    Reasons for verification failure:
    1. The steering lock ECU or ID code box (immobiliser code ECU) is malfunctioning.
    2. There is a problem with the communication between ECUs.
    3. An ECU is replaced, but is not registered.
    4. An ECU is replaced with an ECU which has a code already stored in it.



NG
Go to step 16
OK


14.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).

  1. Perform registration (refer to Service Bulletin).

  1. Turn the engine switch on (IG).

  1. Turn the steering wheel and check the steering condition.

    OK:
    Steering is unlocked.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END 

15.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

  1. Perform registration (refer to Service Bulletin).

  1. Use the Data List to check if S code certification is functioning properly again.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Check
    Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END 

16.REPLACE STEERING LOCK ACTUATOR ASSEMBLY
  1. Replace the steering lock ECU (steering lock actuator assembly) with a new one (Click here).

  1. Perform registration (refer to Service Bulletin).

  1. Use the Data List to check if L code certification is functioning properly again.

    Entry&Start 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Check
    Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG
    OK: Verification result normal
    NG: Verification result abnormal
    When a malfunction is present:
    1. The ID code for the ID code box (immobiliser code ECU) or steering lock ECU is not registered or the ID code box (immobiliser code ECU) or steering lock ECU is malfunctioning.
    2. The steering cannot be locked.
    3. The steering cannot be unlocked (the engine cannot be started).

    OK:
    OK is displayed on the intelligent tester.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END