SMART ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG) |

| Problem Symptom | Data List Item | Active Test Item |
| Power source mode does not change to on (IG) but does change to on (ACC) | Power Source Control
| - |
| 1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INTEGRATION RELAY) |
Disconnect the A43 connector from the certification ECU (smart key ECU assembly).
Disconnect the 1C and 1E connectors from the No. 2 integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A43-9 (IG2D) - 1C-8 | Always | Below 1 Ω |
| 1E-2 - Body ground | Always | Below 1 Ω |
| A43-9 (IG2D) or 1C-8 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY) |
![]() |
Remove the No. 1 integration relay (for 2AR-FE) (Click here).
Remove the No. 1 integration relay (for 2GR-FE) (Click here).
Remove the No. 1 integration relay (for 6AR-FSE) (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1A-1 - 1D-3 | Battery voltage not applied to terminals 1C-8 and 1E-2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1C-8 and 1E-2 | Below 1 Ω |
| *a | Component without harness connected (No. 1 Integration Relay) |
| Result | Proceed to |
| OK | A |
| NG (for 2AR-FE) | B |
| NG (for 2GR-FE) | C |
| NG (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the I78 connector from the certification ECU (smart key ECU assembly).
Disconnect the 3A connector from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I78-6 (IG1D) - 3A-27 | Always | Below 1 Ω |
| 3B-7 - Body ground | Always | Below 1 Ω |
| I78-6 (IG1D) and 3A-27 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2, IG1 NO. 3 AND IG1 NO. 4 RELAY) |
Remove the instrument panel junction block assembly (Click here).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (Click here).
Measure the resistance according to the value(s) in the table below.

| *A | for LHD | *B | for RHD |
| *a | Component without harness connected (Instrument Panel Junction Block Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
| Battery voltage not applied to terminals 3A-27 and 3B-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 3A-27 and 3B-7 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| Battery voltage not applied to terminals 3A-27 and 3B-7 | 10 kΩ or higher |
| Battery voltage applied to terminals 3A-27 and 3B-7 | Below 1 Ω |
|
| ||||
| OK | |
| 5.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Measure the voltage according to the value(s) in the table below.

| *a | Component with harness connected (Certification ECU (Smart Key ECU Assembly)) | - | - |
| Tester Connection | Condition | Specified Condition |
| A43-9 (IG2D) - Body ground | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
| I78-6 (IG1D) - Body ground | Engine switch on (ACC) → Engine switch on (IG) | 1 V or less → 9 V or higher |
|
| ||||
| OK | ||
| ||