PARKING BRAKE CABLE (for TMC, TMMR Made) > REMOVAL |
| 1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for LHD) |
| 2. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY (for RHD) |
| 3. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for LHD) |
![]() |
Pull up the parking brake pedal claw.
![]() |
Remove the adjusting nut.
![]() |
Remove the clip from the No. 1 parking brake cable assembly.
Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.
| 4. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for RHD) |
![]() |
Pull up the parking brake pedal claw.
![]() |
Remove the adjusting nut.
![]() |
Remove the clip from the No. 1 parking brake cable assembly.
Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.
| 5. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
| *1 | Parking Brake Equalizer |
| *2 | No. 2 Parking Brake Cable Assembly |
| *3 | No. 3 Parking Brake Cable Assembly |
| *4 | No. 4 Parking Brake Cable Assembly |
Separate the No. 2 parking brake cable assembly to remove the parking brake equalizer.
![]() |
Slide the parking brake equalizer and rubber boot.
| *1 | Rubber Boot |
| *2 | Parking Brake Equalizer |
| *3 | No. 4 Parking Brake Cable Assembly |
Remove the No. 4 parking brake cable assembly from the parking brake equalizer.
| 6. REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2AR-FE) |
| 7. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 6AR-FSE) |
| 8. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR |
for 2AR-FE, 6AR-FSE:
![]() |
Remove the 3 nuts and front No. 2 floor heat insulator.
| 9. SEPARATE PARKING BRAKE SHOE LEVER |
| 10. REMOVE NO. 2 FLOOR UNDER COVER (for LH Side) |
for TMC Made:
![]() |
Remove the screw and 2 clips.
![]() | Nut (attached to under cover) |
![]() | Screw |
Disengage the 6 nuts and remove the No. 2 floor under cover.
for TMMR Made:
![]() |
Remove the 2 clips.
![]() | Nut (attached to under cover) |
Disengage the 6 nuts and remove the No. 2 floor under cover.
| 11. REMOVE NO. 1 FLOOR UNDER COVER (for RH Side) |
for TMC Made:
![]() |
Remove the screw.
![]() | Nut (attached to under cover) |
![]() | Screw |
Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
for TMMR Made:
![]() |
Disengage the 5 nuts and 2 clips, and remove the No. 1 floor under cover.
![]() | Nut (attached to under cover) |
| 12. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Remove the clip from the No. 3 parking brake cable assembly.
![]() |
Remove the 2 bolts and separate the No. 3 parking brake cable assembly.
Remove the 4 bolts, nut and No. 3 parking brake cable assembly.

| 13. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP |
Remove the No. 2 parking brake cable clamp from the No. 3 parking brake cable assembly.