Home › Brake › PARKING BRAKE › PARKING BRAKE CABLE (for TMMK Made)

PARKING BRAKE CABLE (for TMMK Made) > REMOVAL

for Preparation Click here


HINT:
  1. The following procedure is for the No. 1 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. Use the same procedure for the No. 3 parking brake cable assembly and No. 2 parking brake cable assembly.



1. REMOVE PARKING BRAKE CONTROL PEDAL ASSEMBLY
(Click here)


2. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY


    C239385
  1. Pull up the parking brake pedal claw.

    NOTICE:
    Do not damage the No. 1 parking brake cable assembly.



    C239384
  1. Remove the adjusting nut.



    C239386
  1. Remove the clip from the No. 1 parking brake cable assembly.

  1. Remove the No. 1 parking brake cable assembly from the parking brake pedal assembly.



3. REMOVE REAR DOOR SCUFF PLATE LH


    B395176E01
  1. Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

  1. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

  1. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

    HINT:
    Disengage the claws from the front side of the rear door scuff plate LH.



4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
  1. Disconnect the rear door opening trim weatherstrip LH.



5. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)


    B271081
  1. Disengage the 3 claws and remove the lap belt outer anchor cover.



6. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



7. REMOVE CENTER PILLAR LOWER GARNISH LH


    B278989
  1. Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.



8. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure as for the LH side.



9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedure as for the LH side.



10. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:
Use the same procedure as for the LH side.



11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH


    B271082
  1. Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.



12. REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:
Use the same procedure as for the LH side.



13. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)


14. REMOVE FRONT SEAT ASSEMBLY RH
  1. for Power Seat:

    HINT:
    Use the same procedure as for the LH side (Click here).

  1. for Manual Seat: (Click here)



15. REMOVE AUDIO AMPLIFIER COVER (for 10 Speakers)


    E223732
  1. Using a clip remover, remove the 2 clips and audio amplifier cover.



16. REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)


    E223733
  1. Remove the bolt and disconnect the ground wire.

  1. Disconnect each connector and disengage the clamp.



    E223734
  1. Remove the bolt.

  1. Disengage the 2 guides and remove the stereo component amplifier assembly with bracket.



17. REMOVE FLOOR CARPET HOOK


    E227413E02
  1. Disengage the 6 guides.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



    E227415E02
  1. Disengage the 6 claws and remove the 6 floor carpet hooks.
    Text in Illustration 
    *A
    for LH Side
    *B
    for RH Side



18. REMOVE NO. 4 CROSS MEMBER FLOOR REINFORCEMENT SUB-ASSEMBLY


    E227149
  1. Remove the screw.



    E227150
  1. Disengage the guide to disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

  1. Turn back the floor carpet to a position where the No. 4 cross member floor reinforcement sub-assembly can be removed.



    C239387
  1. Remove the 8 bolts and No. 4 cross member floor reinforcement sub-assembly.



19. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY


    C239388E01
  1. Separate the No. 3 parking brake cable assembly from the parking brake equalizer.
    Text in Illustration 
    *1
    Parking Brake Equalizer
    *2
    No. 2 Parking Brake Cable Assembly
    *3
    No. 3 Parking Brake Cable Assembly
    *4
    No. 4 Parking Brake Cable Assembly

  1. Separate the No. 2 parking brake cable assembly to remove the parking brake equalizer.



    C239389E01
  1. Slide the parking brake equalizer and rubber boot.
    Text in Illustration 
    *1
    Rubber Boot
    *2
    Parking Brake Equalizer
    *3
    No. 4 Parking Brake Cable Assembly

  1. Remove the No. 4 parking brake cable assembly from the parking brake equalizer.



20. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


21. REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR


    C239390
  1. Remove the 3 nuts and front No. 2 floor heat insulator.



22. REMOVE PARKING BRAKE SHOE LEVER
(Click here)


23. REMOVE NO. 2 FLOOR UNDER COVER (for LH Side)


    C308787
  1. Remove the 2 bolts, screw and 2 clips.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Screw
    V100137
    Nut (attached to under cover)

  1. Disengage the 3 nuts and remove the No. 2 floor under cover.



24. REMOVE NO. 1 FLOOR UNDER COVER (for RH Side)


    C308788
  1. Remove the 2 bolts and screw.
    Text in Illustration 
    V100135
    Bolt
    V100136
    Screw
    V100137
    Nut (attached to under cover)

  1. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.



25. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY


    C239391
  1. Remove the clip from the No. 3 parking brake cable assembly.



    C239392
  1. Remove the bolt and separate the No. 3 parking brake cable assembly.



  1. Remove the 4 bolts, nut and No. 3 parking brake cable assembly.


    C239393



26. REMOVE NO. 2 PARKING BRAKE CABLE CLAMP
  1. Remove the No. 2 parking brake cable clamp.