Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1234    Yaw Rate Sensor

DTC    C1472    Acceleration Sensor

for Preparation Click here


DESCRIPTION

The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

HINT:
If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0123 (Lost Communication with Yaw Rate Sensor Module) is output. When U0123 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 first.

DTCs may be stored if one of the following occurs:
  1. Yaw rate and acceleration sensor circuit malfunction.
  2. Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.
  3. Yaw rate and acceleration sensor signal malfunction.

DTC No.
DTC Detection Condition
Trouble Area
C1234
Any of the following is detected:
  1. The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off.
  2. The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven.
  3. The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s.
  4. The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven.
  5. After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped.
  6. After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off.
  7. After the VSC system has started, but before the vehicle has started off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more.
  8. The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more.
  9. The change of the yaw rate sensor value within 0.04 seconds is abnormal.
  10. The value from the yaw rate sensor is judged as abnormal based on the skid control ECU estimation.
  1. Sensor installation
  2. Yaw rate and acceleration sensor (Airbag sensor assembly)
  3. Yaw rate and acceleration sensor circuit
C1472
Any of the following is detected:
  1. With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more.
  2. The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven.
  3. The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more.
  1. Sensor installation
  2. Yaw rate and acceleration sensor (Airbag sensor assembly)
  3. Yaw rate and acceleration sensor circuit

WIRING DIAGRAM


C246787E16


INSPECTION PROCEDURE

HINT:
When U0123 and/or U0126 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 and/or U0126 first (Click here).

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. At a speed of 30 km/h (18 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.

  1. Turn the ignition switch to ON again and check that no CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    CAN communication system DTC is not output.
    A
    CAN communication system DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
  1. Turn the ignition switch off.

  1. Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly (Click here for TMC, TMMR made or Click here for TMMK made).

    OK:
    The sensor should be tightened to the specified torque.
    The sensor should not be tilted.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for TMC, TMMR Made)
    B
    NG (for TMMK Made)
    C



B
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY (Click here)

C
INSTALL AIRBAG SENSOR ASSEMBLY CORRECTLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C239271E03
  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the yaw rate and acceleration sensor (airbag sensor assembly) connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I47-21 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)


    C239271E04
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I47-25 (E1) - Body ground
    Always
    Below 1 Ω
    I47-26 (E2) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))

    Result:

    Result
    Proceed to
    OK (for TMC, TMMR Made)
    A
    OK (for TMMK Made)
    B
    NG
    C

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)
A

REPLACE AIRBAG SENSOR ASSEMBLY (Click here)