Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM

DTC    B1447/47    Rear Air Mix Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The No. 3 air conditioning radiator damper servo sub-assembly (rear air mix) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 3 air conditioning radiator damper servo sub-assembly (rear air mix) to any position. As a result, the amount of air passing through the heater core after passing through the evaporator is adjusted, and the temperature of the air blowing toward the rear is controlled.
The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

HINT:
Confirm that there are no mechanical problems because this DTC can be output when either a damper link or the damper is mechanically locked.


DTC No.
DTC Detection Condition
Trouble Area
B1447/47
Rear air mix damper position does not change even if air conditioning amplifier assembly operates No. 3 air conditioning radiator damper servo sub-assembly (rear air mix)
  1. No. 3 air conditioning radiator damper servo sub-assembly (rear air mix)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E229253E05


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Operate the rear side temperature adjustment switch.

  1. Enter the following menus: Body / Air Conditioner / Data List.

  1. Check the value(s) by referring to the table below.

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Mix Servo Actual Pulse(R)
    No. 3 air conditioning radiator damper servo sub-assembly (rear air mix) pulse / Min.: 0, Max.: 255
    MAX. COLD: 113 (pulse)
    MAX. HOT: 29 (pulse)
    -

    OK:
    The display is as specified in the Normal Condition column.


    Result:

    Result
    Proceed to
    NG
    A
    OK (When troubleshooting according to Problem Symptoms Table)
    B
    OK (When troubleshooting according to the DTC)
    C



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
A


2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Air Conditioner / Active Test.

  1. Check the operation by referring to the table below.

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Air Mix Servo Targ Pulse
    No. 3 air conditioning radiator damper servo sub-assembly (rear air mix) pulse
    Min.: 0, Max.: 255
    Operates between 29 and 113 pulses

    OK:
    Air temperature changes in accordance with each control range.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.REPLACE NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (REAR AIR MIX)
  1. Replace the No. 3 air conditioning radiator damper servo sub-assembly (rear air mix) (Click here).

    HINT:
    Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1447/47 is output
    A
    DTC B1447/47 is not output
    B



B
END (NO. 3 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY WAS DEFECTIVE)
A


4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
  1. Replace the air conditioning harness assembly (Click here).

    HINT:
    Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or a known good one and check that the condition returns to normal.

  1. Check for the DTC.

    Result:
    Result
    Proceed to
    DTC B1447/47 is output
    A
    DTC B1447/47 is not output
    B



B
END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)
A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)