Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

DTC    B2799    Engine Immobiliser System Malfunction

DTC    B279986    Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid

for Preparation Click here


DESCRIPTION

  1. w/ Entry Function on Driver Door except TMMK Made:
    When there are communication malfunctions between the ECM and ID code box (immobiliser code ECU), or when the communication ID codes do not match, the ECM stores this DTC.
  2. w/o Entry Function on Driver Door or for TMMK Made:
    When there are communication malfunctions between the ECM and certification ECU (smart key ECU assembly), or when the communication ID codes do not match, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B2799
Either condition is met (1 trip detection logic*3):
  1. A malfunction in the communication or communication lines between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.
  2. A matching communication code cannot be verified during communication between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2.
  1. ID code box (immobiliser code ECU)*1
  2. Certification ECU (smart key ECU assembly)*2
  3. ECM
  4. Wire harness or connector
Either condition is met:
  1. Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal depressed, the engine switch is pressed while carrying the key). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).
  2. 10 seconds after the engine switch is turned on (IG) after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the engine switch being turned on (IG), and DTCs are stored after 6 seconds).
  1. *1: w/ Entry Function on Driver Door except TMMK Made
  2. *2: w/o Entry Function on Driver Door or for TMMK Made
  3. *3: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started
-

Related Data List and Active Test 
DTC Code
Data List and Active Test
  1. B2799*1
  2. B279986*2
-
  1. *1: for 2GR-FE or 2AR-FE
  2. *2: for 6AR-FSE

WIRING DIAGRAM


B278902E05


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

  1. *1: w/o Entry Function on Driver Door or for TMMK Made
  2. *2: w/ Entry Function on Driver Door except TMMK Made

HINT:
When DTC B2799*1 or B279986*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

  1. *1: for 2GR-FE or 2AR-FE
  2. *2: for 6AR-FSE
1.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


2.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


3.CHECK FOR DTC
  1. Start the engine.

  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

    OK:
    DTC B2799*1 or B279986*2 is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (DTC B2799*1 or B279986*2 is output) (w/o Entry Function on Driver Door or for TMMK Made)
    B
    NG (DTC B2799 is output) (w/ Entry Function on Driver Door except TMMK Made)
    C
    NG (Other DTCs are output)
    D

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE



B
Go to step 4

C
Go to step 13

D
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

4.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the A25*1 or A84*2 ECM connector.

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A43-14 (EFII) - A25-29 (IMO)
    Always
    Below 1 Ω
    A43-14 (EFII) or A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    A43-13 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    A43-13 (EFIO) or A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 6AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A43-14 (EFII) - A84-45 (IMO)
    Always
    Below 1 Ω
    A43-14 (EFII) or A84-45 (IMO) - Body ground
    Always
    10 kΩ or higher
    A43-13 (EFIO) - A84-28 (IMI)
    Always
    Below 1 Ω
    A43-13 (EFIO) or A84-28 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFII)


  1. Using an oscilloscope, check the waveform.


    B380585E01


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    *b
    Approximately 160 ms
    *c
    Approximately 270 ms
    *d
    Waveform

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A43-14 (EFII) - Body ground
    Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    OK:
    The waveform is similar to that shown in the illustration.

    Result:
    Result
    Proceed to
    Normal waveform
    A
    Terminal IMO stuck low (2.4 V or less)
    B
    Terminal IMO stuck high (12 V), or has abnormal wavelength or shape (for 2AR-FE)
    C
    Terminal IMO stuck high (12 V), or has abnormal wavelength or shape (for 6AR-FSE)
    D



B
Go to step 9

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)
A


6.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)


  1. Using an oscilloscope, check the waveform.


    B380586E01


    Text in Illustration 
    *a
    Component with harness connected
    (Certification ECU (Smart Key ECU Assembly))
    *b
    Approximately 160 ms
    *c
    Approximately 270 ms
    *d
    Waveform

    Measurement Condition:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    A43-13 (EFIO) - Body ground
    Engine switch on (IG) using registered electrical key transmitter sub-assembly
    2 V/DIV., 500 ms./DIV.
    Pulse generation
    (See waveform)

    OK:
    The waveform is similar to that shown in the illustration.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


8.CHECK WHETHER ENGINE STARTS
  1. Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the engine switch on (IG).

  1. Check that the engine starts 5 seconds after the engine switch was turned on (IG).

    OK:
    Engine starts normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 6AR-FSE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

9.INSPECT ECM (IMO TERMINAL VOLTAGE)


    A255690E78
  1. Disconnect the A25*1 or A84*2 ECM connector.

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    A25-29 (IMO) - Body ground
    Engine switch on (IG) using registered electrical key transmitter sub-assembly
    Terminal IMO stuck low (2.4 V or less)
    Terminal IMO stuck high (12 V) or abnormal waveform
    for 6AR-FSE 
    Tester Connection
    Condition
    Specified Condition
    A84-45 (IMO) - Body ground
    Engine switch on (IG) using registered electrical key transmitter sub-assembly
    Terminal IMO stuck low (2.4 V or less)
    Terminal IMO stuck high (12 V) or abnormal waveform

    Text in Illustration 
    *A
    for 2AR-FE
    *B
    for 6AR-FSE
    *a
    Front view of wire harness connector
    (to ECM)

    Result:
    Result
    Proceed to
    Terminal IMO stuck low (2.4 V or less)
    A
    Terminal IMO stuck high (12 V) or abnormal waveform (for 2AR-FE)
    B
    Terminal IMO stuck high (12 V) or abnormal waveform (for 6AR-FSE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A


10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


11.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


12.CHECK WHETHER ENGINE STARTS
  1. Using an electrical key transmitter sub-assembly which is registered to the vehicle, turn the engine switch on (IG).

  1. Check that the engine starts 5 seconds after the engine switch was turned on (IG).

    OK:
    Engine starts normally.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 6AR-FSE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE) 

13.REGISTER ECU COMMUNICATION ID
Register the ECU communication ID.

HINT:
Refer to Service Bulletin.


NEXT


14.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


15.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

OK:
DTC B2799 is not output.



NG
Go to step 16
OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE) 

16.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - ECM)
  1. Disconnect the I20 ID code box (immobiliser code ECU) connector.

  1. Disconnect the A25 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-30 (IMO)
    Always
    Below 1 Ω
    I20-3 (EFII) or A25-30 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-31 (IMI)
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-3 (EFII) - A25-29 (IMO)
    Always
    Below 1 Ω
    I20-3 (EFII) or A25-29 (IMO) - Body ground
    Always
    10 kΩ or higher
    I20-4 (EFIO) - A25-28 (IMI)
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-28 (IMI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.REPLACE ECM
  1. Temporarily replace the ECM with a new one (Click here for 2GR-FE , Click here for 2AR-FE).


NEXT


18.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


19.CHECK FOR DTC
  1. Perform "DTC Output Confirmation Operation" procedure.

  1. Check for DTCs (Click here).

    OK:
    DTC B2799 is not output.



NG
REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
OK

END (ECM WAS DEFECTIVE)