Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver

for Preparation Click here


DESCRIPTION

  1. w/o Manual (SOS) Switch:
    The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
    Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.
  1. w/ Manual (SOS) Switch:
    The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
    Using this circuit, the telematics transceiver sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly via the telematics transceiver.

WIRING DIAGRAM


E268440E31


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System (w/ Manual (SOS) Switch) (Click here).

1.CHECK MICROPHONE (OPERATION CHECK)


    E277821
  1. Enter the "Microphone Check" screen.
    Refer to Check Microphone in Operation Check (Click here).

  1. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

    OK:
    Check result is normal.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/o Manual (SOS) switch
    A
    w/ Manual (SOS) switch
    B



B
Go to step 5
A


3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-4 (MACC) - S7-14 (MACC)*1
    Always
    Below 1 Ω
    I155-4 (MACC) - S14-14 (MACC)*2
    Always
    Below 1 Ω
    I155-5 (MIN+) - S7-13 (MCO+)*1
    Always
    Below 1 Ω
    I155-5 (MIN+) - S14-13 (MCO+)*2
    Always
    Below 1 Ω
    I155-19 (MIN-) - S7-12 (MCO-)*1
    Always
    Below 1 Ω
    I155-19 (MIN-) - S14-12 (MCO-)*2
    Always
    Below 1 Ω
    I155-6 (SNS2) - S7-15 (SNS2)*1
    Always
    Below 1 Ω
    I155-6 (SNS2) - S14-15 (SNS2)*2
    Always
    Below 1 Ω
    I155-4 (MACC) or S7-14 (MACC)*1 - Body ground
    Always
    10 kΩ or higher
    I155-4 (MACC) or S14-14 (MACC)*2 - Body ground
    Always
    10 kΩ or higher
    I155-5 (MIN+) or S7-13 (MCO+)*1 - Body ground
    Always
    10 kΩ or higher
    I155-5 (MIN+) or S14-13 (MCO+)*2 - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) or S7-12 (MCO-)*1 - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) or S14-12 (MCO-)*2 - Body ground
    Always
    10 kΩ or higher
    I155-18 (SGND) - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) or S7-15 (SNS2)*1 - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) or S14-15 (SNS2)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E289735E20
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I155-4 (MACC) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I155-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



B
Go to step 10
A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)  

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-6 (SNS2) - S7-15 (SNS2)*1
    Always
    Below 1 Ω
    I155-6 (SNS2) - S14-15 (SNS2)*2
    Always
    Below 1 Ω
    I155-6 (SNS2) or S7-15 (SNS2)*1 - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) or S14-15 (SNS2)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the I218 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-5 (MIN+) - I218-18 (MCO+)
    Always
    Below 1 Ω
    I155-19 (MIN-) - I218-19 (MCO-)
    Always
    Below 1 Ω
    I155-5 (MIN+) or I218-18 (MCO+) - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) or I218-19 (MCO-) - Body ground
    Always
    10 kΩ or higher
    I155-18 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-33 (MCVD) - S7-14 (MACC)*1
    Always
    Below 1 Ω
    I218-33 (MCVD) - S14-14 (MACC)*2
    Always
    Below 1 Ω
    I218-34 (MCI+) - S7-13 (MCO+)*1
    Always
    Below 1 Ω
    I218-34 (MCI+) - S14-13 (MCO+)*2
    Always
    Below 1 Ω
    I218-35 (MCI-) - S7-12 (MCO-)*1
    Always
    Below 1 Ω
    I218-35 (MCI-) - S14-12 (MCO-)*2
    Always
    Below 1 Ω
    I218-33 (MCVD) or S7-14 (MACC)*1 - Body ground
    Always
    10 kΩ or higher
    I218-33 (MCVD) or S14-14 (MACC)*2 - Body ground
    Always
    10 kΩ or higher
    I218-34 (MCI+) or S7-13 (MCO+)*1 - Body ground
    Always
    10 kΩ or higher
    I218-34 (MCI+) or S14-13 (MCO+)*2 - Body ground
    Always
    10 kΩ or higher
    I218-35 (MCI-) or S7-12 (MCO-)*1 - Body ground
    Always
    10 kΩ or higher
    I218-35 (MCI-) or S14-12 (MCO-)*2 - Body ground
    Always
    10 kΩ or higher
    I218-32 (SGND) - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E289735E21
  1. Disconnect the I218 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-18 (SGND) - Body ground
    Always
    Below 1 Ω
    I155-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for TMMK Made)
    B
    NG
    (for TMC, TMMR Made)
    C



B
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)

C
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
A


9.INSPECT TELEMATICS TRANSCEIVER


    E353877E02
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I218-33 (MCVD) - Body ground
    Ignition switch ACC
    4 to 6 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-35 (MCI-) - Body ground
    Always
    Below 1 Ω
    I218-32 (SGND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Telematics Transceiver)



NG
REPLACE TELEMATICS TRANSCEIVER (Click here)
OK


10.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Remove the roof console box assembly (telephone microphone assembly).
    for TMMK Made: Click here
    for TMC, TMMR Made: Click here



    E187117E59
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    15 (SNS2) - 12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    OK
    A
    NG
    (for TMMK Made)
    B
    NG
    (for TMC, TMMR Made)
    C



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)

C
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A


11.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Turn the ignition switch to ACC.

  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector*1.



    E187122E60
  1. Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

    1. *1: except TMMK Made
    2. *2: for TMMK Made

    Result:
    Result
    Proceed to
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output.
    A
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output.
    (for TMMK Made)
    B
    A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output.
    (for TMC, TMMR Made)
    C

    Text in Illustration 
    *a
    Component with harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))
    *1
    except TMMK Made
    *2
    for TMMK Made



B
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)

C
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)