NAVIGATION SYSTEM (for Radio and Display Type) > Microphone Circuit between Microphone and Radio Receiver |

| 1.CHECK MICROPHONE (OPERATION CHECK) |
![]() |
Enter the "Microphone Check" screen.
Refer to Check Microphone in Operation Check (Click here).
When a voice is input to the microphone, check that the microphone input level meter changes according to the input voice.
|
| ||||
| OK | ||
| ||
| 2.CONFIRM MODEL |
Choose the model to be inspected.
| Model | Proceed to |
| w/o Manual (SOS) Switch | A |
| w/ Manual (SOS) Switch | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the I155 radio and display receiver assembly connector.
Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-4 (MACC) - S7-14 (MACC) | Always | Below 1 Ω |
| I155-5 (MIN+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I155-19 (MIN-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I155-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I155-4 (MACC) or S7-14 (MACC) - Body ground | Always | 10 kΩ or higher |
| I155-5 (MIN+) or S7-13 (MCO+) - Body ground | Always | 10 kΩ or higher |
| I155-19 (MIN-) or S7-12 (MCO-) - Body ground | Always | 10 kΩ or higher |
| I155-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| I155-6 (SNS2) or S7-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-18 (SGND) - Body ground | Always | Below 1 Ω |
| I155-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
| NG | A |
| OK | B |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the I155 radio and display receiver assembly connector.
Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I155-6 (SNS2) or S7-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER) |
Disconnect the I155 radio and display receiver assembly connector.
Disconnect the I218 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-5 (MIN+) - I218-18 (MCO+) | Always | Below 1 Ω |
| I155-19 (MIN-) - I218-19 (MCO-) | Always | Below 1 Ω |
| I155-5 (MIN+) or I218-18 (MCO+) - Body ground | Always | 10 kΩ or higher |
| I155-19 (MIN-) or I218-19 (MCO-) - Body ground | Always | 10 kΩ or higher |
| I155-18 (SGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) |
Disconnect the I218 telematics transceiver connector.
Disconnect the S7 roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I218-33 (MCVD) - S7-14 (MACC) | Always | Below 1 Ω |
| I218-34 (MCI+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I218-35 (MCI-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I218-33 (MCVD) or S7-14 (MACC) - Body ground | Always | 10 kΩ or higher |
| I218-34 (MCI+) or S7-13 (MCO+) - Body ground | Always | 10 kΩ or higher |
| I218-35 (MCI-) or S7-12 (MCO-) - Body ground | Always | 10 kΩ or higher |
| I218-32 (SGND) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
![]() |
Disconnect the I218 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I155-18 (SGND) - Body ground | Always | Below 1 Ω |
| I155-19 (MIN-) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Radio and Display Receiver Assembly) |
|
| ||||
| OK | |
| 9.INSPECT TELEMATICS TRANSCEIVER |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I218-33 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I218-35 (MCI-) - Body ground | Always | Below 1 Ω |
| I218-32 (SGND) - Body ground | Always | Below 1 Ω |
| *a | Component with harness connected (Telematics Transceiver) |
|
| ||||
| OK | |
| 10.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Remove the roof console box assembly (telephone microphone assembly) (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 15 (SNS2) - 12 (MCO-) | Always | Below 1 Ω |
| *a | Component without harness connected (Roof Console Box Assembly (Telephone Microphone Assembly)) |
|
| ||||
| OK | |
| 11.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) |
Turn the ignition switch to ACC.
![]() |
Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S7 roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. | B |
| *a | Component with harness connected (Roof Console Box Assembly (Telephone Microphone Assembly)) |
|
| ||||
| A | ||
| ||