Home › Power Source / Network · NETWORKING › CAN COMMUNICATION SYSTEM

DTC    U0265    Lost Communication with Parking Assist Monitor Module

for Preparation Click here


DESCRIPTION


DTC No.
DTC Detection Condition
Trouble Area
U0265
No communication from the rear television camera assembly continues.
  1. Rear television camera assembly branch line or connector
  2. Power source circuit of rear television camera assembly
  3. Rear television camera assembly ground circuit
  4. Rear television camera assembly

HINT:
This diagnosis procedure is for when DTC U0265 is output by the network gateway ECU (GTS display: Gateway).


WIRING DIAGRAM


C313302E03


INSPECTION PROCEDURE

NOTICE:
  1. Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  2. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
  4. After performing repairs, perform the procedure listed in DTC Reproduction Method and confirm that the DTCs are not output again.
  5. DTC check procedure: Turn the ignition switch to ON and wait at least 10 seconds.
  6. After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).

HINT:
  1. Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  2. Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

1.RECONFIRM DTC OUTPUT
  1. Reconfirm DTCs.

    HINT:
    If DTC U1002 is output from Gateway of the network gateway ECU, this indicates a sub bus 2 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 2.

    Result:
    Result
    Proceed to
    U1002 is not output from network gateway ECU
    (GTS display: Gateway)
    A
    U1002 is output from network gateway ECU
    (GTS display: Gateway)
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


2.RECONFIRM DTC OUTPUT (PARKING ASSIST SYSTEM)
  1. Reconfirm DTCs.

  1. Enter the following menus: Chassis / Advanced Parking Guidance/Parking Assist Monitor / Trouble Codes.

    Result:
    Result
    Proceed to
    C1621 is not output
    A
    C1621 is output
    B



B
GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC (Click here)
A


3.CHECK FOR OPEN IN SUB BUS 2 LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)
  1. Disconnect the cable from the negative (-) battery terminal.



    C294680E07
  1. Disconnect the T20 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T20-1 (CANH) - T20-4 (CANN)
    Cable disconnected from negative (-) battery terminal
    54 to 69 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)

    Result:
    Result
    Proceed to
    OK (for TMC, TMMR Made)
    A
    OK (for TMMK Made)
    B
    NG
    C



C
REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)

B
REPLACE REAR TELEVISION CAMERA ASSEMBLY (for TMMK Made) (Click here)
A

REPLACE REAR TELEVISION CAMERA ASSEMBLY (for TMC, TMMR Made) (Click here)