Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/ Smart Entry and Start System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

DTC    B279A12    Engine Immobiliser System Circuit Short to Battery

for Preparation Click here


DESCRIPTION

  1. w/ Entry Function on Driver Door except TMMK Made:
    When the communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU) is stuck high, the ECM stores this DTC.
  2. w/o Entry Function on Driver Door or for TMMK Made:
    When the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
DTC Output Confirmation Operation
B279A
The communication line (IMI - EFIO) between the ECM and ID code box (immobiliser code ECU)*1 or certification ECU (smart key ECU assembly)*2 is stuck high (1 trip detection logic*3).
  1. Wire harness or connector (disconnection or break in wire harness is main cause)
  2. ID code box (immobiliser code ECU)*1
  3. Certification ECU (smart key ECU assembly)*2
  4. ECM
Turn the engine switch on (IG) and wait 6 seconds.
  1. *1: w/ Entry Function on Driver Door except TMMK Made
  2. *2: w/o Entry Function on Driver Door or for TMMK Made
  3. *3: Only output while a malfunction is present.

Vehicle Condition and Fail-safe Operation when Malfunction Detected 
Vehicle Condition when Malfunction Detected
Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops)
Engine cannot be started

Related Data List and Active Test 
DTC Code
Data List and Active Test
  1. B279A*1
  2. B279A12*2
-
  1. *1: for 2GR-FE or 2AR-FE
  2. *2: for 6AR-FSE

WIRING DIAGRAM


B278904E04


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the certification ECU (smart key ECU assembly)*1 or ID code box (immobiliser code ECU)*2, refer to Service Bulletin.
  2. After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.

  1. *1: w/o Entry Function on Driver Door or for TMMK Made
  2. *2: w/ Entry Function on Driver Door except TMMK Made

HINT:
When DTC B279A*1 or B279A12*2 and the certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.

  1. *1: for 2GR-FE or 2AR-FE
  2. *2: for 6AR-FSE
1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Turn the engine switch on (IG) and wait 10 seconds.

  1. Check for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC B279A*1 or B279A12*2 is output
    A
    DTC B279A*1 or B279A12*2 and other DTCs are output
    B

    HINT:
    If DTCs other than DTC B279A*1 or B279A12*2 are output, troubleshoot those DTCs first.

    1. *1: for 2GR-FE or 2AR-FE
    2. *2: for 6AR-FSE



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK CONNECTION OF CONNECTOR
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4.CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU)*1 OR CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)*2 - ECM)
  1. Disconnect the I20 ID code box (immobiliser code ECU) connector.*1

  1. Disconnect the A43 certification ECU (smart key ECU assembly) connector.*2

  1. Disconnect the A25*3 or A84*4 ECM connector.

    1. *1: w/ Entry Function on Driver Door except TMMK Made
    2. *2: w/o Entry Function on Driver Door or for TMMK Made
    3. *3: for 2GR-FE or 2AR-FE
    4. *4: for 6AR-FSE

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 2GR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-4 (EFIO) - A25-31 (IMI)
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-31 (IMI) - Body ground
    Always
    10 kΩ or higher
    for 2AR-FE 
    Tester Connection
    Condition
    Specified Condition
    I20-4 (EFIO) - A25-28 (IMI)*1
    A43-13 (EFIO) - A25-28 (IMI)*2
    Always
    Below 1 Ω
    I20-4 (EFIO) or A25-28 (IMI) - Body ground*1
    A43-13 (EFIO) or A25-28 (IMI) - Body ground*2
    Always
    10 kΩ or higher
    for 6AR-FSE 
    Tester Connection
    Condition
    Specified Condition
    A43-13 (EFIO) - A84-28 (IMI)
    Always
    Below 1 Ω
    A43-13 (EFIO) or A84-28 (IMI) - Body ground
    Always
    10 kΩ or higher

    1. *1: w/ Entry Function on Driver Door except TMMK Made
    2. *2: w/o Entry Function on Driver Door or for TMMK Made

Result:
Result
Proceed to
OK (w/ Entry Function on Driver Door except TMMK Made)
A
OK (w/o Entry Function on Driver Door or for TMMK Made)
B
NG
C



B
Go to step 10

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


5.REPLACE ID CODE BOX (IMMOBILISER CODE ECU)
  1. Replace the ID code box (immobiliser code ECU) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


6.REGISTER RECOGNITION CODES
  1. Register the recognition codes in the ECUs.

    HINT:
    Refer to Service Bulletin.


NEXT


7.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK DTC OUTPUT
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A is not output.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2GR-FE)
    B
    NG (for 2AR-FE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE) 

10.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
  1. Replace the certification ECU (smart key ECU assembly) with a new one.

    HINT:
    Refer to Service Bulletin.


NEXT


11.REGISTER RECOGNITION CODES
  1. Register the key.

    HINT:
    Refer to Service Bulletin.


NEXT


12.REGISTER ECU COMMUNICATION ID
  1. Register the ECU communication ID.

    HINT:
    Refer to Service Bulletin.


NEXT


13.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


14.CHECK FOR DTC
  1. Check for DTCs (Click here).

    HINT:
    Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.

    OK:
    DTC B279A*1 or B279A12*2 is not output.

    1. *1: for 2AR-FE
    2. *2: for 6AR-FSE

    Result:
    Result
    Proceed to
    OK
    A
    NG (for 2AR-FE)
    B
    NG (for 6AR-FSE)
    C



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)
A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)