Home › Power Source / Network · NETWORKING › LIN COMMUNICATION SYSTEM

DTC    B2321    Driver Side Door ECU Communication Stop

for Preparation Click here


DESCRIPTION

This DTC is stored when LIN communication between the power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.
DTC Detection Condition
Trouble Area
B2321
No communication between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more.
  1. Power window regulator motor assembly (for driver door)
  2. Main body ECU (multiplex network body ECU)
  3. Multiplex network master switch assembly
  4. Wire harness or connector
  5. DOOR F/L fuse (w/ Jam Protection Function on 4 Windows for LHD)
  6. DOOR F/R fuse (w/ Jam Protection Function on 4 Windows for RHD)
  7. DOOR NO. 2 fuse (w/ Jam Protection Function on Front Door Windows)

WIRING DIAGRAM


B399789E01


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When a power window regulator motor assembly is replaced or removed and reinstalled, it requires initialization,
    1. w/ Jam Protection Function on 4 Windows: Click here
      w/ Jam Protection Function on Front Door Windows: Click here
  3. When using the intelligent tester to troubleshoot with the ignition switch off:
    Connect the intelligent tester to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

1.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.

    Result:
    Result
    Proceed to
    Only DTC B2321 is output.
    A
    DTC B1206 and B2321 are output simultaneously.
    B

    HINT:
    When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.



B
GO TO DTC B1206 (Click here)
A


2.CHECK HARNESS AND CONNECTOR (MASTER SWITCH - DRIVER DOOR POWER WINDOW REGULATOR MOTOR)
  1. Disconnect the K3*1, J3*2 or K15*3 multiplex network master switch connector.

  1. Disconnect the K9*1, *3 or J9*2 power window regulator motor (for driver door) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K3-16 (LIN2) - K9-9 (LIN)*1
    J3-16 (LIN2) - J9-9 (LIN)*2
    K15-7 (LIN2) - K9-9 (LIN)*3
    Always
    Below 1 Ω
    K3-16 (LIN2) - Body ground*1
    J3-16 (LIN2) - Body ground*2
    K15-7 (LIN2) - Body ground*3
    Always
    10 kΩ or higher

    1. *1: w/ Jam Protection Function on 4 Windows for LHD
    2. *2: w/ Jam Protection Function on 4 Windows for RHD
    3. *3: w/ Jam Protection Function on Front Door Windows



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


    B399790E01
  1. Remove the multiplex network master switch assembly.

    1. w/ Jam Protection Function on 4 Windows: Click here
      w/ Jam Protection Function on Front Door Windows: Click here


Text in Illustration 
*A
w/ Jam Protection Function on 4 Windows
*B
w/ Jam Protection Function on Front Door Windows
*a
Component without harness connected
(Multiplex Network Master Switch Assembly)
*b
Component without harness connected
(Multiplex Network Master Switch Assembly)
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    16 (LIN2) - 17 (LIN1)*1
    Always
    Below 1 Ω
    7 (LIN2) - 6 (LIN1)*2
    Always
    Below 1 Ω
    16 (LIN2) - Body ground*1
    Always
    10 kΩ or higher
    7 (LIN2) - Body ground*2
    Always
    10 kΩ or higher

    1. *1: w/ Jam Protection Function on 4 Windows
    2. *2: w/ Jam Protection Function on Front Door Windows

    Result:
    Result
    Proceed to
    OK
    A
    NG (w/ Jam Protection Function on 4 Windows)
    B
    NG (w/ Jam Protection Function on Front Door Windows)
    C



B
REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)

C
REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (Click here)
A


4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR - BATTERY, BODY GROUND)
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    K9-2 (B) - Body ground*1
    J9-2 (B) - Body ground*2
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K9-1 (GND) - Body ground*1
    J9-1 (GND) - Body ground*2
    Always
    Below 1 Ω

    1. *1: for LHD
    2. *2: for RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)
  1. Replace the power window regulator motor assembly (for driver door).

    1. w/ Jam Protection Function on 4 Windows: Click here
      w/ Jam Protection Function on Front Door Windows: Click here


NEXT


6.CHECK DTC OUTPUT
  1. Clear the DTC (Click here).

  1. Recheck for DTCs.

    OK:
    DTC B2321 is not output.



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK

END (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR) WAS DEFECTIVE)