Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

When the mirror adjust switch is operated, the main body ECU (multiplex network body ECU) detects the switch operation and sends the mirror adjust switch signal to the outer mirror control ECU assembly (front passenger door) via CAN communication. On receiving the signal, the outer mirror control ECU assembly (front passenger door) operates the vertical and horizontal mirror motors, which are built into the outer rear view mirror assembly (front passenger door), to adjust the mirror surface position.

WIRING DIAGRAM


B293969E66


INSPECTION PROCEDURE

NOTICE:
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly (Click here).

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mirror Selection SW (R)
    Mirror select switch signal for RH mirror / ON or OFF
    ON: Mirror select switch in R position
    OFF: Mirror select switch off or in L position
    -
    Mirror Position SW (R)
    Mirror adjust switch signal (Right) / ON or OFF
    ON: Mirror adjust switch pressed right
    OFF: Mirror adjust switch not pressed right
    Check with the mirror select switch in the R position
    Mirror Position SW (L)
    Mirror adjust switch signal (Left) / ON or OFF
    ON: Mirror adjust switch pressed left
    OFF: Mirror adjust switch not pressed left
    Check with the mirror select switch in the R position
    Mirror Position SW (Up)
    Mirror adjust switch signal (Up) / ON or OFF
    ON: Mirror adjust switch pressed up
    OFF: Mirror adjust switch not pressed up
    Check with the mirror select switch in the R position
    Mirror Position SW (Dwn)
    Mirror adjust switch signal (Down) / ON or OFF
    ON: Mirror adjust switch pressed down
    OFF: Mirror adjust switch not pressed down
    Check with the mirror select switch in the R position

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 4
OK


2.PERFORM ACTIVE TEST USING GTS
  1. Enter the following menus: Body Electrical / Mirror R / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Mirror R / Mirror L 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Up/Down
    Mirror vertical operation
    Up / Down
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the mirror up or down.
    3. This operation can be confirmed by watching the mirror move in the desired direction.
    Mirror Right/Left
    Mirror horizontal operation
    Right / Left
    1. Operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the mirror right or left.
    3. This operation can be confirmed by watching the mirror move in the desired direction.

    OK:
    Power mirror operation is normal.



NG
Go to step 3
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) (Click here)  

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
  1. Remove the outer rear view mirror assembly (front passenger door) (Click here).

  1. Inspect the outer rear view mirror assembly (front passenger door) (mirror surface) (Click here).



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (Click here)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) (Click here)  

4.INSPECT OUTER MIRROR SWITCH ASSEMBLY
  1. Remove the outer mirror switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below (Click here).



NG
REPLACE OUTER MIRROR SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)
  1. Disconnect the K11 connector from the outer mirror switch assembly.

  1. Disconnect the I12 connector from the main body ECU (multiplex network body ECU).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-2 (E) - I12-15 (MIRE)
    Always
    Below 1 Ω
    K11-3 (M+) - I12-13 (MIRB)
    Always
    Below 1 Ω
    K11-1 (MSW) - I12-14 (MIRS)
    Always
    Below 1 Ω
    K11-2 (E) - Body ground
    Always
    10 kΩ or higher
    K11-3 (M+) - Body ground
    Always
    10 kΩ or higher
    K11-1 (MSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)