Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM (w/ Memory)

POWER MIRROR CONTROL SYSTEM (w/ Memory) > Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

for Preparation Click here


SYSTEM DESCRIPTION

The main body ECU (multiplex network body ECU) receives the retractable outer mirror switch signal from the outer mirror switch assembly. The main body ECU then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on the signal, each outer mirror control ECU assembly retracts or returns the outer rear view mirror assembly.

WIRING DIAGRAM


B301483E05


INSPECTION PROCEDURE

NOTICE:
The power mirror control system (w/ Memory) uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system (w/ Memory) after confirming that the communication systems are functioning properly (Click here).

1.READ VALUE USING GTS
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the Data List according to the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Outer Mirror Fold SW
    Retractable outer mirror switch signal / ON or OFF
    ON: Retractable outer mirror switch in retract position
    OFF: Retractable outer mirror switch in driving position
    -

    OK:
    On the GTS screen, ON or OFF is displayed accordingly.



NG
Go to step 5
OK


2.PERFORM ACTIVE TEST USING GTS
  1. Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.

  1. Perform the Active Test according to the display on the GTS.

    Mirror L / Mirror R 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Mirror Fold/Return
    Mirror retract operation
    Fold / Return
    1. operate with engine switch on (IG) and the vehicle stopped.
    2. This test activates the Fold / Return.
    3. This operation can be confirmed by watching the mirror move in the desired direction.

    Result:
    Result
    Proceed to
    Outer rear view mirror assemblies operate normally
    A
    Outer rear view mirror assembly (front passenger door) does not operate normally
    B
    Outer rear view mirror assembly (driver door) does not operate normally
    C



B
Go to step 3

C
Go to step 4
A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)
  1. Remove the outer rear view mirror assembly (front passenger door) (Click here).

  1. Inspect the outer rear view mirror assembly (front passenger door) (Click here).



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) (Click here)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) (Click here)  

4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)
  1. Remove the outer rear view mirror assembly (driver door) (Click here).

  1. Inspect the outer rear view mirror assembly (driver door) (Click here).



NG
REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) (Click here)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) (Click here)  

5.INSPECT OUTER MIRROR SWITCH ASSEMBLY
  1. Remove the outer mirror switch assembly (Click here).

  1. Inspect the outer mirror switch assembly (Click here).



NG
REPLACE OUTER MIRROR SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - MAIN BODY ECU)
  1. Disconnect the I12 connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    K11-8 (MR) - I12-28 (RET)
    Always
    Below 1 Ω
    K11-8 (MR) - Body ground
    Always
    10 kΩ or higher
    K11-4 (E2) - I12-15 (MIRE)
    Always
    Below 1 Ω
    K11-4 (E2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)