DTC B14A3 Front Passenger Side Solar Sensor Short Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| B14A3 | Short in passenger side solar sensor (automatic light control sensor) circuit |
|

| 1.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Body / Air Conditioner / Data List.
Check the value(s) by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Solar Sensor (P Side) | Front passenger side solar sensor (automatic light control sensor) / Min.: 0 Max.: 255 | Front passenger side solar sensor (automatic light control sensor) value increases as brightness increases | - |
| Result | Proceed to |
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC (for TMC, TMMR Made)) | C |
| OK (When troubleshooting according to the DTC (for TMMK Made)) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT) |
![]() |
Disconnect the I61 solar sensor (automatic light control sensor) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I61-6 (CLTB) - I61-3 (CLTE) | Ignition switch off | Below 1 V |
| I61-6 (CLTB) - I61-3 (CLTE) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Solar Sensor (Automatic Light Control Sensor)) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the I61 solar sensor (automatic light control sensor) connector.
Disconnect the I77 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I77-32 (TSP) - I61-1 (TSL)*1 | Always | Below 1 Ω |
| I77-32 (TSP) - I61-2 (TSR)*2 | Always | Below 1 Ω |
| I77-32 (TSP) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) |
![]() |
Remove the solar sensor (automatic light control sensor) (Click here(for TMC, TMMR Made)) (Click here (for TMMK Made)).
Reconnect the I61 solar sensor (automatic light control sensor) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I61-1 (TSL) - I61-3 (CLTE)*1 | Sensor is subjected to electric light | 0.8 to 4.3 V |
| I61-1 (TSL) - I61-3 (CLTE)*1 | Sensor is covered with a cloth | Below 0.8 V |
| I61-2 (TSR) - I61-3 (CLTE)*2 | Sensor is subjected to electric light | 0.8 to 4.3 V |
| I61-2 (TSR) - I61-3 (CLTE)*2 | Sensor is covered with a cloth | Below 0.8 V |
| *A | for RHD |
| *B | for LHD |
| *a | Component with harness connected (Solar Sensor (Automatic Light Control Sensor)) |
| Result | Proceed to |
| OK (for TMC, TMMR Made) | A |
| OK (for TMMK Made) | B |
| NG (for TMC, TMMR Made) | C |
| NG (for TMMK Made) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)) |
Disconnect the I13 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I13-20 (CLTB) - I61-6 (CLTB) | Always | Below 1 Ω |
| I13-22 (CLTE) - I61-3 (CLTE) | Always | Below 1 Ω |
| I13-20 (CLTB) - Body ground | Always | 10 kΩ or higher |
| I13-22 (CLTE) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||