AUDIO AND VISUAL SYSTEM (for Radio and Display Type) > OPERATION CHECK |
| CHECK PANEL & STEERING SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.
![]() |
Panel & Steering Switch Check Mode
| Display | Content |
| *a: Switch condition | "Pushed" is displayed when any switch is pushed. |
| *b: Number of switches pushed |
|
| *c: Rotary switch direction | Direction of rotary switch is displayed. |
Operate each switch and check that the switch conditions are correctly displayed.
| CHECK TOUCH SWITCH |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Touch Switch" from the "Function Check/Setting I" screen.
![]() |
Touch Switch Check
Touch the display anywhere in the open area to perform the check when the "Touch Switch Check" screen is displayed.
| CHECK MICROPHONE |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Microphone Check" from the "Function Check/Setting I" screen.
![]() |
Microphone Check
| Display | Content |
| *a: Microphone input level meter | Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels. |
When speaking into the microphone, check that the microphone input level meter changes according to the input level.
| CHECK VEHICLE SIGNAL |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "Vehicle Signal" from the "Function Check/Setting I" screen.
![]() |
Vehicle Signal Check Mode
| Display | Content |
| Battery | Battery voltage is displayed. |
| IG | Ignition switch ON/OFF state is displayed. |
| PKB | Parking brake ON/OFF state is displayed. |
| REV | Reverse signal ON/OFF state is displayed. |
| SPEED | Vehicle speed is displayed in km/h. |
| TAIL | Tail signal (light control switch) ON/OFF state is displayed. |
| ADIM/TCAN | Brightness state DIM (with)/BRIGHT (without) is displayed. |
When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.
| CHECK HANDS-FREE VOICE QUALITY SETTING |
Enter diagnostic mode (Click here).
![]() |
Select "Function Check/Setting" from the "Service Menu" screen.
![]() |
Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.
![]() |
Hands-Free Voice Quality Setting
| *a | Numeric Keypad |
| *b | Setting Button |
| *c | Reset Button |
If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.
When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.
| Parameter | Target Phenomenon | Voice Quality Type | Positive Effect of Changing Voice Quality | Negative Effect of Changing Voice Quality |
| A (Noise) | The other party hears background noise when listening to your voice. | 1000 | The amount of background noise the other party hears when listening to your voice is reduced. | The volume of voice the other party hears when listening to your voice may temporarily drop. |
| B (Noise) | The other party hears a lot of background noise when listening to your voice. | 2000 | The amount of background noise the other party hears when listening to your voice is sharply reduced. | The volume of voice the other party hears when listening to your voice may temporarily drop. |
| C (Echo) | The other party hears weak echoes. | 0100 | The amount of echo is reduced (low level). | Sound quality of the other party deteriorates (low level). |
| D (Echo) | The other party hears strong echoes. | 0200 | The amount of echo is reduced (high level). | Sound quality of the other party deteriorates (high level). |
| Parameter | Target Phenomenon | Voice Quality Type | Positive Effect of Changing Voice Quality | Negative Effect of Changing Voice Quality |
| A+C | The other party hears background noise and weak echoes when listening to your voice. | 1100 |
|
|
| A+D | The other party hears background noise and strong echoes when listening to your voice. | 1200 |
|
|
| B+C | The other party hears a lot of background noise and weak echoes when listening to your voice. | 2100 |
|
|
| B+D | The other party hears a lot of background noise and strong echoes when listening to your voice. | 2200 |
|
|
| CHECK SPEAKER |
Turn audio mode on and play any audio source.
Enter diagnostic mode (Click here).
![]() |
Select "Failure Diagnosis" from the "Service Menu" screen.
![]() |
Select "System Check" from the "Failure Diagnosis" screen.
![]() |
Select "SP Check ON" from the "System Check Mode" screen.
Check the speaker wiring and check that the speakers are functioning properly.
Sound stops when any of the following conditions are met:
"SP Check OFF" is selected.
The ignition switch is turned off.
Diagnostic mode is turned off.
The screen is changed to another screen.
Audio mode is turned off.
| CHECK SOFTWARE ERROR HISTORY |
Check Software Error History.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.
When an item is stored for Software Error History, record it before repairing the radio and display receiver assembly.
| Error Description | Trigger | Detail |
| Software Reset | Navi Microcomputer | Hexadecimal Number |
| Audio Microcomputer | ||
| CAN Microcomputer | ||
| No Video Signal | Front Monitor | |
| Rear Monitor | ||
| MOST Cold Restart | Always |
Clear software error history.
When DTCs are cleared using any of the following operations, Software Error History will be cleared as well (Click here).
| CHECK OPTICAL DISC ERROR HISTORY |
Check Optical Disc Error History.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.
When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.
| Display | Content |
| Error Type | Displays the type of error. |
| Device | Displays the malfunctioning device. |
| Date | Displays the date and time that the malfunction occurred. |
| Error Type | Detection Condition | Action |
| Read Error | When a disc read error occurs. | Proceed to next suspected area shown in Problem Symptoms Table (Click here) |
| Disc damaged/upside down/dirty | When it is determined that any of the following is the cause of the disc read error:
| |
| Cannot determine disc type | An unsuitable disc is inserted. | |
| DPS error | When an error occurs while decoding MP3/WMA/AAC files. | |
| Some files are corrupt |
| |
| Some files cannot be found |
| |
| Copy protection violation | When a file with copyright protection that cannot be played back is played back. |
| Device | Component |
| DVD-P | Radio and display receiver assembly*1 |
| CD-P | Radio and display receiver assembly*2 |
| R-Seat DVD-P | Not available |
Clear optical disc error history.
When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well (Click here).
| CHECK VIDEO DEVICE CONNECTION CHECK |
Check Video Device Connection Check.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.
When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.
| Error Detected Image Line (Type) | Areas to be Checked |
| H/U - > Separate Display (GVIF) | Not available |
| H/U - > Full RSE (GVIF) | Not available |
| RSE - > Seat Back Display RH (GVIF) | Not available |
| RSE - > Seat Back Display LH (GVIF) | Not available |
| Rear Camera - > H/U (NTSC) | NTSC video signal between the radio and display receiver assembly and rear television camera assembly |
| IPA/BGM/PVM ECU - > Separate Display (GVIF) | Not available |
| IPA/BGM/PVM ECU - > H/U (NTSC) | Not available |
| IPA/BGM/PVM ECU - > H/U (GVIF) | Not available |
Clear video device connection check.
When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well (Click here).