FRONT LOWER SUSPENSION ARM (for 2AR-FE) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. REMOVE FRONT WHEELS |
| 4. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 5. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD) |
w/ Windshield Deicer System:
![]() |
Disengage the 2 clamps.
Disconnect the connector and separate the wire harness from the front outer cowl top panel sub-assembly.
w/ Heated Windshield Defroster System:
![]() |
Disengage the 4 clamps.
Disconnect the 2 connectors and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 6. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD) |
![]() |
Disengage the 2 clamps and separate the wire harness from the front outer cowl top panel sub-assembly.
![]() |
Remove the 10 bolts and front outer cowl top panel sub-assembly.
| 7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY |
![]() |
Disconnect the vacuum switching valve assembly from the air cleaner hose.
![]() |
Disconnect the mass air flow meter connector and 2 wire harness clamps from the air cleaner cap sub-assembly.
![]() |
Separate the fuel vapor feed hose from the air cleaner hose.
![]() |
Disconnect the ventilation hose from the cylinder head cover.
![]() |
Loosen the hose clamp and disconnect the air cleaner hose from the throttle with motor body assembly.
![]() |
Release the 2 clamps and remove the air cleaner cap sub-assembly.
| 8. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
| 9. REMOVE AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Disconnect the wire harness clamp.
Remove the 2 bolts and air cleaner case sub-assembly.
| 10. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH |
| 11. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH |
| 12. REMOVE ENGINE UNDER COVER LH |
| 13. REMOVE ENGINE UNDER COVER RH |
| 14. REMOVE FRONT FENDER APRON SEAL LH (for LH Side) |
| 15. REMOVE FRONT FENDER APRON SEAL RH (for RH Side) |
| 16. SEPARATE FRONT ENGINE MOUNTING INSULATOR |
![]() |
Remove the 3 nuts to separate the front engine mounting insulator from the front frame assembly.
| 17. REMOVE ENGINE MOUNTING INSULATOR LH (for LH Side) |
![]() |
Remove the 2 hole plugs.
Remove the 4 nuts from the engine mounting insulator LH.
![]() |
Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration. While ensuring that there is no interference from the components surrounding the engine, tilt the engine assembly with transaxle to a position that allows the engine mounting insulator LH to be removed.
| *1 | Jack |
| *2 | Wooden Block |
![]() |
Remove the engine mounting insulator LH from the front frame assembly.
| 18. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side) |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly LH from the front lower ball joint assembly.
![]() |
Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.
Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.
| 19. SEPARATE EARTH WIRE (for RH Side) |
![]() |
Remove the bolt and separate the earth wire from the engine moving control rod bracket.
| 20. REMOVE NO. 2 ENGINE MOUNTING STAY RH (for RH Side) |
![]() |
Remove the 2 bolts and No. 2 engine mounting stay RH.
| 21. REMOVE ENGINE MOVING CONTROL ROD BRACKET (for RH Side) |
![]() |
Remove the 4 bolts and engine moving control rod bracket.
| 22. REMOVE ENGINE MOUNTING INSULATOR RH (for RH Side) |
Remove the 2 hole plugs.
![]() |
Remove the 4 nuts from the engine mounting insulator RH.
![]() |
Using a jack and a wooden block, support the engine assembly with transaxle at the position shown in the illustration. While ensuring that there is no interference from the components surrounding the engine, tilt the engine assembly with transaxle to a position that allows the engine mounting insulator RH to be removed.
| *1 | Jack |
| *2 | Wooden Block |
![]() |
Remove the engine mounting insulator RH from the front frame assembly.
| 23. REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side) |
![]() |
Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly RH from the front lower ball joint assembly.
![]() |
Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly RH from the front frame assembly.
Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly RH.