Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B1579    Voice Recognition Microphone Disconnected

for Preparation Click here


DESCRIPTION

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code
DTC Detection Condition
Trouble Area
B1579
Microphone signal is lost
  1. Roof console box assembly (telephone microphone assembly)
  2. Telematics transceiver*
  3. Radio and display receiver assembly
  4. Harness or connector
  1. *: w/ Manual (SOS) Switch

WIRING DIAGRAM


E250444E25


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System (w/ Manual (SOS) Switch) (Click here).

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    E289390E13
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-19 (MIN-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Radio and Display Receiver Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Model
    Proceed to
    w/ Manual (SOS) Switch
    A
    w/o Manual (SOS) Switch
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-35 (MCI-) - S7-12 (MCO-)*1
    Always
    Below 1 Ω
    I218-35 (MCI-) - S14-12 (MCO-)*2
    Always
    Below 1 Ω
    I218-35 (MCI-) or S7-12 (MCO-)*1 - Body ground
    Always
    10 kΩ or higher
    I218-35 (MCI-) or S7-12 (MCO-)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the I218 telematics transceiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-19 (MIN-) - I218-19 (MCO-)
    Always
    Below 1 Ω
    I155-19 (MIN-) or I218-19 (MCO-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-6 (SNS2) - S7-15 (SNS2)*1
    Always
    Below 1 Ω
    I155-6 (SNS2) - S14-15 (SNS2)*2
    Always
    Below 1 Ω
    I155-6 (SNS2) or S7-15 (SNS2)*1 - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) or S14-15 (SNS2)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT TELEMATICS TRANSCEIVER


    E353877E05
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-35 (MCI-) - Body ground
    Always
    Below 1 Ω

  1. Proceed to the next step based on the inspection result.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    Text in Illustration 
    *a
    Component with harness connected
    (Telematics Transceiver)



B
Go to step 8
A

REPLACE TELEMATICS TRANSCEIVER (Click here)  

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
  1. Disconnect the I155 radio and display receiver assembly connector.

  1. Disconnect the S7 roof console box assembly (telephone microphone assembly) connector*1.

  1. Disconnect the S14 roof console box assembly (telephone microphone assembly) connector*2.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I155-6 (SNS2) - S7-15 (SNS2)*1
    Always
    Below 1 Ω
    I155-6 (SNS2) - S14-15 (SNS2)*2
    Always
    Below 1 Ω
    I155-19 (MIN-) - S7-12 (MCO-)*1
    Always
    Below 1 Ω
    I155-19 (MIN-) - S14-12 (MCO-)*2
    Always
    Below 1 Ω
    I155-6 (SNS2) or S7-15 (SNS2)*1 - Body ground
    Always
    10 kΩ or higher
    I155-6 (SNS2) or S14-15 (SNS2)*2 - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) or S7-12 (MCO-)*1 - Body ground
    Always
    10 kΩ or higher
    I155-19 (MIN-) or S14-12 (MCO-)*2 - Body ground
    Always
    10 kΩ or higher

    1. *1: except TMMK Made
    2. *2: for TMMK Made



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
  1. Remove the roof console box assembly (telephone microphone assembly).
    for TMMK Made: Click here.
    except TMMK Made: Click here.



    E187117E58
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    15 (SNS2) - 12 (MCO-)
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Roof Console Box Assembly (Telephone Microphone Assembly))



NG
REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)