Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1AB1    Short to +B in Outer Mirror Indicator(Slave)

for Preparation Click here


DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No.
DTC Detection Condition
Trouble Area
C1AB1
When either of the following conditions is met:
  1. Blind spot monitor main switch (warning canceling switch assembly) is on.
  1. The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.
  1. Outer rear view mirror LH (outer rear view mirror indicator LH)
  2. Outer rear view mirror assembly LH
  3. Wire harness or connector
  4. Blind spot monitor sensor LH
  5. Outer mirror control ECU assembly LH

WIRING DIAGRAM


E233743E36


INSPECTION PROCEDURE

NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH))
  1. Disconnect the T17 blind spot monitor sensor LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T17-4 (OMIL) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 3
OK

REPLACE BLIND SPOT MONITOR SENSOR LH (Click here)  

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)
  1. Disconnect the IND1 outer rear view mirror LH (outer rear view mirror indicator LH) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T17-4 (OMIL) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 4
OK

REPLACE OUTER REAR VIEW MIRROR LH (OUTER REAR VIEW MIRROR INDICATOR LH) (Click here)  

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
  1. Disconnect the z18 outer mirror control ECU assembly LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T17-4 (OMIL) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 5
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (Click here)  

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)
  1. Disconnect the K12 outer mirror control ECU assembly LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    T17-4 (OMIL) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH (Click here)