Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM

DTC    C1AB0    Short to +B in Outer Mirror Indicator(Master)

for Preparation Click here


DESCRIPTION

This DTC is stored when the blind spot monitor sensor RH detects a +B short in the outer rear view mirror indicator RH.

DTC No.
DTC Detection Condition
Trouble Area
C1AB0
When either of the following conditions is met:
  1. Blind spot monitor main switch (warning canceling switch assembly) is on.
  1. The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.
  1. Outer rear view mirror RH (outer rear view mirror indicator RH)
  2. Outer rear view mirror assembly RH
  3. Wire harness or connector
  4. Blind spot monitor sensor RH
  5. Outer mirror control ECU assembly RH

WIRING DIAGRAM


E233743E35


INSPECTION PROCEDURE

NOTICE:
When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

1.CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH))
  1. Disconnect the O43 blind spot monitor sensor RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (OMIR) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 3
OK

REPLACE BLIND SPOT MONITOR SENSOR RH (Click here)  

3.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER REAR VIEW MIRROR ASSEMBLY RH)
  1. Disconnect the IND2 outer rear view mirror RH (outer rear view mirror indicator RH) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (OMIR) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 4
OK

REPLACE OUTER REAR VIEW MIRROR RH (OUTER REAR VIEW MIRROR INDICATOR RH) (Click here)  

4.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
  1. Disconnect the z17 outer mirror control ECU assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (OMIR) - Body ground
    Ignition switch ON
    Below 1 V



NG
Go to step 5
OK

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH (Click here)  

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR RH - OUTER MIRROR CONTROL ECU ASSEMBLY RH)
  1. Disconnect the J10 outer mirror control ECU assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    O43-4 (OMIR) - Body ground
    Ignition switch ON
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH (Click here)