Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

LIGHTING SYSTEM > Turn Signal Switch Circuit

for Preparation Click here


DESCRIPTION

The combination meter receives the turn signal switch information and controls the turn signal lights.

WIRING DIAGRAM


E314639E01


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Turn Signal Switch (Right)
    Turn signal switch (right) signal/ON or OFF
    ON: Turn signal switch (right) on
    OFF: Turn signal switch (right) off
    -
    Turn Signal Switch (Left)
    Turn signal switch (left) signal/ON or OFF
    ON: Turn signal switch (left) on
    OFF: Turn signal switch (left) off
    -
    Turn Switch Signal (Full Turn)
    Turn signal switch (full turn) signal/ON or OFF
    ON: Turn signal switch (left or right) on
    OFF: Turn signal switch (left and right) off
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Remove the headlight dimmer switch assembly (for TMC, TMMR Made: Click here), (for TMMK Made: Click here).



  1. for LHD:



      E223779E35
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      12 (TR) - 15 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      11 (TL) - 15 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      13 (CR) - 15 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      12 (TR) - 15 (EL)
      Turn signal switch in right turn position
      Below 1 Ω
      13 (CR) - 15 (EL)
      Turn signal switch in full right turn position
      Below 1 Ω
      11 (TL) - 15 (EL)
      Turn signal switch in left turn position
      Below 1 Ω
      13 (CR) - 15 (EL)
      Turn signal switch in full left turn position
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)



  1. for RHD:



      E223779E47
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      20 (TR) - 16 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      19 (TL) - 16 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      18 (CR) - 16 (EL)
      Turn signal switch in neutral position
      10 kΩ or higher
      20 (TR) - 16 (EL)
      Turn signal switch in right turn position
      Below 1 Ω
      18 (CR) - 16 (EL)
      Turn signal switch in full right turn position
      Below 1 Ω
      19 (TL) - 16 (EL)
      Turn signal switch in left turn position
      Below 1 Ω
      18 (CR) - 16 (EL)
      Turn signal switch in full left turn position
      Below 1 Ω

      Text in Illustration 
      *a
      Component without harness connected
      (Headlight Dimmer Switch Assembly)

      Result:

      Result
      Proceed to
      OK
      A
      NG (for TMC, TMMR Made)
      B
      NG (for TMMK Made)
      C



B
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)

C
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY (Click here)
A


3.CHECK HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the I17 combination meter assembly connector.

  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I25-12 (TR) - I17-9 (ER)
      Always
      Below 1 Ω
      I25-11 (TL) - I17-10 (EL)
      Always
      Below 1 Ω
      I25-13 (CR) - I17-8 (SW)
      Always
      Below 1 Ω
      I25-15 (EL) - Body ground
      Always
      Below 1 Ω
      I17-9 (ER) - Body ground
      Always
      10 kΩ or higher
      I17-10 (EL) - Body ground
      Always
      10 kΩ or higher
      I17-8 (SW) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      I25-20 (TR) - I17-9 (ER)
      Always
      Below 1 Ω
      I25-19 (TL) - I17-10 (EL)
      Always
      Below 1 Ω
      I25-18 (CR) - I17-8 (SW)
      Always
      Below 1 Ω
      I25-16 (EL) - Body ground
      Always
      Below 1 Ω
      I17-9 (ER) - Body ground
      Always
      10 kΩ or higher
      I17-10 (EL) - Body ground
      Always
      10 kΩ or higher
      I17-8 (SW) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)