SHIFT LEVER (for TMMK Made) > INSTALLATION |
| 1. INSTALL SHIFT LEVER SUPPORT |
![]() |
Install the shift lever support to the vehicle body with the 4 bolts in the order shown in the illustration.
| 2. INSTALL LOWER SHIFT LEVER ASSEMBLY |
![]() |
Install the lower shift lever assembly to the shift lever support with the 4 bolts in the order shown in the illustration.
Engage the 2 clamps.
Connect the shift lock control ECU connector.
![]() |
Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.
| *1 | Slider |
| *2 | Lock Piece |
| *a | Slide |
| *b | Pull |
Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.
![]() |
Connect the end of the transmission control cable assembly to the lower shift lever assembly.
| *1 | Lock Piece |
Push the lock piece into the adjuster case.
| 3. INSTALL NO. 1 CONSOLE BOX DUCT |
Install the No. 1 console box duct to the lower shift lever assembly with the clip.
| 4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET |
Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.
Engage the guide.
| 5. INSTALL FLOOR CARPET BRACKET LH |
Engage the 2 guides.
Install the floor carpet bracket LH with the 2 clips.
| 6. INSTALL CONSOLE BOX INSERT |
![]() |
Engage the guide and 2 clips as shown in the illustration.
Install the console box insert with the screw <C> or <D>.
| 7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Engage the guide and 2 clips as shown in the illustration.
Install the front No. 2 console box insert with the screw <C> or <D>.
Engage the 2 claws to connect the room temperature sensor.
| 8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY |
Connect each connector.
![]() |
Engage the guide and 2 clips as shown in the illustration.
Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
| 9. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Connect the connector.
Engage the glove compartment light as shown in the illustration.
Engage the clamp.
![]() |
Engage the guide and 2 clips.
Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.
| 10. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| 11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
Connect the connector.
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
| 12. INSTALL INSTRUMENT SIDE PANEL RH |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
| 13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
![]() |
Align the alignment mark (White) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
| *a | Alignment Mark (White) |
| 14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH |
| 15. INSTALL FRONT DOOR SCUFF PLATE RH |
| 16. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
Engage the 4 claws, 9 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.
| 17. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
| 18. INSTALL INSTRUMENT SIDE PANEL LH |
Engage the 3 guides.
![]() |
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
| 19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
| *a | Alignment Mark (Yellow) |
| 20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the clip.
| 21. INSTALL FRONT DOOR SCUFF PLATE LH |
Engage the 10 claws to install the front door scuff plate LH.
| 22. INSTALL REAR CONSOLE BOX ASSEMBLY |
| 23. INSPECT SHIFT LEVER POSITION |
When the shift lever is moved from P to R with the ignition switch ON and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into the position.
Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.
| 24. INSTALL SHIFT LOCK RELEASE BUTTON COVER |
![]() |
Engage the 2 claws to install the shift lock release button cover to the shift position indicator.
| 25. CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 26. PERFORM DIAGNOSTIC SYSTEM CHECK |
| 27. INSPECT SRS WARNING LIGHT |