SHIFT LEVER (for TMMK Made) > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE SHIFT LOCK RELEASE BUTTON COVER |
![]() |
Using a screwdriver, disengage the 2 claws to remove the shift lock release button cover from the shift position indicator.
| *a | Protective Tape |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE REAR CONSOLE BOX ASSEMBLY |
| 5. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.
Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.
Disengage the 6 claws (C) to remove the front door scuff plate LH.
| 6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Pull the cowl side trim sub-assembly LH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.
| 7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
Remove the front door opening trim weatherstrip LH.
| 8. REMOVE INSTRUMENT SIDE PANEL LH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
| 9. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY |
![]() |
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
| 10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
![]() |
Remove the bolt <B> and screw <C> or <D>.
![]() |
Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.
| 11. REMOVE FRONT DOOR SCUFF PLATE RH |
| 12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 14. REMOVE INSTRUMENT SIDE PANEL RH |
![]() |
Using a moulding remover, disengage the 4 claws as shown in the illustration.
![]() |
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
| 15. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
![]() |
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.
| 16. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY |
| 17. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 screws <C> or <D>.
Open the lower instrument panel door.
![]() |
Remove the 3 screws <C> or <D>.
![]() |
Disengage the 2 clips and guide as shown in the illustration.
![]() |
Disengage the clamp.
Disengage the glove compartment light as shown in the illustration.
Disconnect the connector and remove the lower instrument panel sub-assembly.
| 18. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY |
![]() |
Remove the 2 screws <C> or <D>.
![]() |
Disengage the 2 clips and guide as shown in the illustration.
Disconnect each connector to remove the upper console panel sub-assembly.
| 19. REMOVE FRONT NO. 2 CONSOLE BOX INSERT |
![]() |
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
![]() |
Remove the screw <C> or <D>.
![]() |
Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.
| 20. REMOVE CONSOLE BOX INSERT |
![]() |
Remove the screw <C> or <D>.
![]() |
Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.
| 21. REMOVE FLOOR CARPET BRACKET LH |
![]() |
Remove the 2 clips.
Disengage the 2 guides to remove the floor carpet bracket LH.
| 22. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET |
![]() |
Disengage the guide.
Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.
| 23. REMOVE NO. 1 CONSOLE BOX DUCT |
![]() |
Remove the clip and No. 1 console box duct from the lower shift lever assembly.
| 24. REMOVE LOWER SHIFT LEVER ASSEMBLY |
![]() |
Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.
Disengage the 2 claws to disconnect the transmission control cable assembly from the lower shift lever assembly.
![]() |
Disconnect the shift lock control ECU connector.
Disengage the 2 clamps.
![]() |
Remove the 4 bolts and lower shift lever assembly from the shift lever support.
| 25. REMOVE SHIFT LEVER SUPPORT |
![]() |
Remove the 4 bolts and shift lever support from the vehicle body.