DTC B15C3 Speaker Output Short |
| DTC No. | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit |
|
| for TMC Made |

| for TMMK Made |


| 1.CHECK MODEL |
Choose the model to be inspected.
| Result | Proceed to |
| for TMC Made | A |
| for TMMK Made | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BODY GROUND) |
Disconnect the I64 and I65 navigation receiver assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Disconnect the O18 and O21 rear speaker assembly connectors.
Measure the resistance between the navigation receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I64-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| I64-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| I64-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| I64-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| I65-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| I65-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| I65-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| I65-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) |
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I83-3 (+) - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | |
| 5.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (TWR+) - 2 (TWR-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWR+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWR-) | Always | Below 1 Ω |
| 4 (TWL+) - 2 (TWL-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (TWL+) | Always | Below 1 Ω |
| 1 (-) - 2 (TWL-) | Always | Below 1 Ω |
| *A | for RH |
| *B | for LH |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 6.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Replace the front No. 2 speaker assembly with a new or known good one (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check that no DTCs are output.
|
| ||||
| OK | ||
| ||
| 7.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BODY GROUND) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Disconnect the I60 front No. 3 speaker assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Disconnect the O22 rear speaker assembly connector.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) - Body ground | Always | 10 kΩ or higher |
| I68-12 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I68-13 (CTR+) - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) - Body ground | Always | 10 kΩ or higher |
| I68-10 (SR+) - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) - Body ground | Always | 10 kΩ or higher |
| I68-8 (WF1+) - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (+) - 2 (-) | Always | 4.6 to 6.6 Ω |
| *a | Component without harness connected (Front No. 1 Speaker Assembly) |
|
| ||||
| OK | |
| 10.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 - 3 | Always | 3.4 to 5.2 Ω |
| *a | Component without harness connected (Front No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 11.REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
Replace the front No. 2 speaker assembly with a new or known good one (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check that no DTCs are output.
|
| ||||
| OK | ||
| ||
| 12.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
Remove the front No. 3 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| *a | Component without harness connected (Front No. 3 Speaker Assembly) |
|
| ||||
| OK | |
| 13.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
Remove the rear No. 2 speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 6.8 to 10.2 Ω |
| *a | Component without harness connected (Rear No. 2 Speaker Assembly) |
|
| ||||
| OK | |
| 14.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | Always | 4.8 to 6.8 Ω |
| *a | Component without harness connected (Rear Speaker Assembly) |
|
| ||||
| OK | ||
| ||