DTC B15C3 Speaker Output Short |
| DTC No. | DTC Detection Condition | Trouble Area |
| B15C3 | A short is detected in the speaker output circuit |
|


| 1.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY OR SPEAKER - BODY GROUND) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Disconnect the I60 front No. 3 speaker assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Disconnect the O22 rear speaker assembly connector.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) or J5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) or J5-2 (-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) or K5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) or K5-2 (-) - Body ground | Always | 10 kΩ or higher |
| I68-13 (CTR+) or I60-2 - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) or I60-1 - Body ground | Always | 10 kΩ or higher |
| I68-10 (SR+) or O19-2 - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) or O19-1 - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) or O20-2 - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) or O20-1 - Body ground | Always | 10 kΩ or higher |
| I68-8 (WF1+) or O22-1 - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) or O22-2 - Body ground | Always | 10 kΩ or higher |
| I68-12 (TWR+) or I84-4 - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) or I84-3 - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) or I2-4 - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) or I2-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here).
|
| ||||
| OK | |
| 3.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
Remove the front No. 3 speaker assembly (Click here).
Inspect the front No. 3 speaker assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
Remove the rear No. 2 speaker assembly (Click here).
Inspect the rear No. 2 speaker assembly (Click here).
|
| ||||
| OK | |
| 5.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
Inspect the rear speaker assembly (Click here).
|
| ||||
| OK | |
| 6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
Inspect the front No. 2 speaker assembly (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check that no DTCs are output.
|
| ||||
| OK | ||
| ||