Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly
  4. Telematics transceiver*
  1. *: w/ Manual (SOS) Switch

WIRING DIAGRAM


E300084E06


E362360E03


INSPECTION PROCEDURE

NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System. (Click here).

1.CONFIRM MODEL
  1. Choose the model to be inspected.

    Result:
    Result
    Proceed to
    w/ Manual (SOS) Switch
    A
    w/o Manual (SOS) Switch
    B



B
Go to step 5
A


2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)
  1. Disconnect the I68 stereo component amplifier assembly connector.

  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the K5 and J5 front No. 1 speaker assembly connectors.

  1. Disconnect the I60 front No. 3 speaker assembly connector.

  1. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.

  1. Disconnect the O22 rear speaker assembly connector.

  1. Disconnect the I2 front No. 2 speaker assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) or K5-2 - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) or I60-2 - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) or I60-1 - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) or O19-2 - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) or O19-1 - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) or O20-2 - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) or O20-1 - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) or O22-1 - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) or O22-2 - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) or I218-2 (SPI+) - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) or I218-3 (SPI-) - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) or I2-4 - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) or I2-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER OR SPEAKERS - BODY GROUND)
  1. Disconnect the I218 telematics transceiver connector.

  1. Disconnect the I84 front No. 2 speaker assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I218-5 (SPO+) or I84-4 - Body ground
    Always
    10 kΩ or higher
    I218-6 (SPO-) or I84-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT TELEMATICS TRANSCEIVER
  1. Remove the telematics transceiver (Click here).



    E169849E36
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2 (SPI+) - 5 (SPO+)
    Always
    Below 1 Ω
    3 (SPI-) - 6 (SPO-)
    Always
    Below 1 Ω
    2 (SPI+) - 3 (SPI-)
    Always
    10 kΩ or higher
    5 (SPO+) - 6 (SPO-)
    Always
    10 kΩ or higher
    2 (SPI+) or 5 (SPO+) - Body ground
    Always
    10 kΩ or higher
    3 (SPI-) or 6 (SPO-) - Body ground
    Always
    10 kΩ or higher

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B

    Text in Illustration 
    *a
    Component without harness connected
    (Telematics Transceiver)



B
Go to step 6
A

REPLACE TELEMATICS TRANSCEIVER (Click here)  

5.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY OR SPEAKERS - BODY GROUND)
  1. Disconnect the I68 stereo component amplifier assembly connector.

  1. Disconnect the J5 and K5 front No. 1 speaker assembly connectors.

  1. Disconnect the I60 front No. 3 speaker assembly connector.

  1. Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.

  1. Disconnect the O22 rear speaker assembly connector.

  1. Disconnect the I84 and I2 front No. 2 speaker assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I68-15 (FR+) or J5-1 - Body ground
    Always
    10 kΩ or higher
    I68-30 (FR-) or J5-2 - Body ground
    Always
    10 kΩ or higher
    I68-11 (FL+) or K5-1 - Body ground
    Always
    10 kΩ or higher
    I68-26 (FL-) or K5-2 - Body ground
    Always
    10 kΩ or higher
    I68-13 (CTR+) or I60-2 - Body ground
    Always
    10 kΩ or higher
    I68-28 (CTR-) or I60-1 - Body ground
    Always
    10 kΩ or higher
    I68-10 (SR+) or O19-2 - Body ground
    Always
    10 kΩ or higher
    I68-25 (SR-) or O19-1 - Body ground
    Always
    10 kΩ or higher
    I68-9 (SL+) or O20-2 - Body ground
    Always
    10 kΩ or higher
    I68-24 (SL-) or O20-1 - Body ground
    Always
    10 kΩ or higher
    I68-8 (WF1+) or O22-1 - Body ground
    Always
    10 kΩ or higher
    I68-23 (WF1-) or O22-2 - Body ground
    Always
    10 kΩ or higher
    I68-12 (TWR+) or I84-4 - Body ground
    Always
    10 kΩ or higher
    I68-27 (TWR-) or I84-3 - Body ground
    Always
    10 kΩ or higher
    I68-14 (TWL+) or I2-4 - Body ground
    Always
    10 kΩ or higher
    I68-29 (TWL-) or I2-3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


7.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY
  1. Remove the front No. 3 speaker assembly (Click here).

  1. Inspect the front No. 3 speaker assembly (Click here).



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


8.INSPECT REAR NO. 2 SPEAKER ASSEMBLY
  1. Remove the rear No. 2 speaker assembly (Click here).

  1. Inspect the rear No. 2 speaker assembly (Click here).



NG
REPLACE REAR NO. 2 SPEAKER ASSEMBLY (Click here)
OK


9.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here).

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK


10.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
  1. Remove the front No. 2 speaker assembly (Click here).

  1. Inspect the front No. 2 speaker assembly (Click here).



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK

END