NAVIGATION SYSTEM (for Navigation Receiver Type) > Speaker Circuit |
| for TMC Made |

| for TMMK Made |


| 1.CHECK MODEL |
Choose the model to be inspected.
| Result | Proceed to |
| for TMC Made | A |
| for TMMK Made | B |
|
| ||||
| A | |
| 2.CHECK SPEAKER (OPERATION CHECK) |
![]() |
Enter the "System Check Mode" screen.
Refer to Check Speaker in Operation Check (Click here).
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the I64 navigation receiver assembly connector.
Disconnect the I83 and I1 front No. 2 speaker assembly connectors.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I64-1 (FR+) - I83-4 (TWR+) | Always | Below 1 Ω |
| I64-5 (FR-) - I83-2 (TWR-) | Always | Below 1 Ω |
| I64-2 (FL+) - I1-4 (TWL+) | Always | Below 1 Ω |
| I64-6 (FL-) - I1-2 (TWL-) | Always | Below 1 Ω |
| I83-3 (+) - J5-1 | Always | Below 1 Ω |
| I83-1 (-) - J5-2 | Always | Below 1 Ω |
| I1-3 (+) - K5-1 | Always | Below 1 Ω |
| I1-1 (-) - K5-2 | Always | Below 1 Ω |
| I64-1 (FR+) or I83-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| I64-5 (FR-) or I83-2 (TWR-) - Body ground | Always | 10 kΩ or higher |
| I64-2 (FL+) or I1-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| I64-6 (FL-) or I1-2 (TWL-) - Body ground | Always | 10 kΩ or higher |
| I83-3 (+) or J5-1 - Body ground | Always | 10 kΩ or higher |
| I83-1 (-) or J5-2 - Body ground | Always | 10 kΩ or higher |
| I1-3 (+) or K5-1 - Body ground | Always | 10 kΩ or higher |
| I1-1 (-) or K5-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
Inspect the front No. 2 speaker assembly (Click here).
Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed (Click here).
|
| ||||
| OK | ||
| ||
| 5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the I65 navigation receiver assembly connector.
Disconnect the O18 and O21 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I65-1 (RR+) - O18-1 | Always | Below 1 Ω |
| I65-3 (RR-) - O18-2 | Always | Below 1 Ω |
| I65-2 (RL+) - O21-1 | Always | Below 1 Ω |
| I65-6 (RL-) - O21-2 | Always | Below 1 Ω |
| I65-1 (RR+) or O18-1 - Body ground | Always | 10 kΩ or higher |
| I65-3 (RR-) or O18-2 - Body ground | Always | 10 kΩ or higher |
| I65-2 (RL+) or O21-1 - Body ground | Always | 10 kΩ or higher |
| I65-6 (RL-) or O21-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
Inspect the rear speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 8.CHECK SPEAKER (OPERATION CHECK) |
![]() |
Enter the "System Check Mode" screen.
Refer to Check Speaker in Operation Check (Click here).
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly | B |
| Front No. 3 speaker assembly | C |
| Rear No. 2 speaker assembly | D |
| Rear speaker assembly | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 9.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the J5 and K5 front No. 1 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-15 (FR+) - J5-1 (+) | Always | Below 1 Ω |
| I68-30 (FR-) - J5-2 (-) | Always | Below 1 Ω |
| I68-11 (FL+) - K5-1 (+) | Always | Below 1 Ω |
| I68-26 (FL-) - K5-2 (-) | Always | Below 1 Ω |
| I68-15 (FR+) or J5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-30 (FR-) or J5-2 (-) - Body ground | Always | 10 kΩ or higher |
| I68-11 (FL+) or K5-1 (+) - Body ground | Always | 10 kΩ or higher |
| I68-26 (FL-) or K5-2 (-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
Remove the front No. 1 speaker assembly (Click here).
Inspect the front No. 1 speaker assembly (Click here
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I84 and I2 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-12 (TWR+) - I84-4 | Always | Below 1 Ω |
| I68-27 (TWR-) - I84-3 | Always | Below 1 Ω |
| I68-14 (TWL+) - I2-4 | Always | Below 1 Ω |
| I68-29 (TWL-) - I2-3 | Always | Below 1 Ω |
| I68-12 (TWR+) or I84-4 - Body ground | Always | 10 kΩ or higher |
| I68-27 (TWR-) or I84-3 - Body ground | Always | 10 kΩ or higher |
| I68-14 (TWL+) or I2-4 - Body ground | Always | 10 kΩ or higher |
| I68-29 (TWL-) or I2-3 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 12.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
Remove the front No. 2 speaker assembly (Click here).
Inspect the front No. 2 speaker assembly (Click here).
Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed (Click here).
|
| ||||
| OK | ||
| ||
| 13.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the I60 front No. 3 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-13 (CTR+) - I60-2 | Always | Below 1 Ω |
| I68-28 (CTR-) - I60-1 | Always | Below 1 Ω |
| I68-13 (CTR+) or I60-2 - Body ground | Always | 10 kΩ or higher |
| I68-28 (CTR-) or I60-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.INSPECT FRONT NO. 3 SPEAKER ASSEMBLY |
Remove the front No. 3 speaker assembly (Click here).
Inspect the front No. 3 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 15.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR NO. 2 SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O19 and O20 rear No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-10 (SR+) - O19-2 | Always | Below 1 Ω |
| I68-25 (SR-) - O19-1 | Always | Below 1 Ω |
| I68-9 (SL+) - O20-2 | Always | Below 1 Ω |
| I68-24 (SL-) - O20-1 | Always | Below 1 Ω |
| I68-10 (SR+) or O19-2 - Body ground | Always | 10 kΩ or higher |
| I68-25 (SR-) or O19-1 - Body ground | Always | 10 kΩ or higher |
| I68-9 (SL+) or O20-2 - Body ground | Always | 10 kΩ or higher |
| I68-24 (SL-) or O20-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 16.INSPECT REAR NO. 2 SPEAKER ASSEMBLY |
Remove the rear No. 2 speaker assembly (Click here).
Inspect the rear No. 2 speaker assembly (Click here).
|
| ||||
| OK | ||
| ||
| 17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
Disconnect the I68 stereo component amplifier assembly connector.
Disconnect the O22 rear speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I68-8 (WF1+) - O22-1 | Always | Below 1 Ω |
| I68-23 (WF1-) - O22-2 | Always | Below 1 Ω |
| I68-8 (WF1+) or O22-1 - Body ground | Always | 10 kΩ or higher |
| I68-23 (WF1-) or O22-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.INSPECT REAR SPEAKER ASSEMBLY |
Remove the rear speaker assembly (Click here).
Inspect the rear speaker assembly (Click here).
|
| ||||
| OK | ||
| ||