Home › Engine / Hybrid System · 6AR-FSE › ENGINE CONTROL › SFI SYSTEM

DTC    P003612    HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Battery

DTC    P003614    HO2S Heater Control Circuit Bank 1 Sensor 2 Circuit Short to Ground or Open

DTC    P102A9E    O2 Sensor Heater Performance Bank 1 Sensor 2 Stuck On

for Preparation Click here


DESCRIPTION

Refer to DTC P013613 .

HINT:
When any of these DTCs are stored, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.


A338252E02


DTC No.
DTC Detection Condition
Trouble Area
P003612
Heated oxygen sensor heater current reaches high limit (1 trip detection logic).
  1. Short in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. ECM
P003614
Heated oxygen sensor heater current is the specified value or less while the heater is operating (1 trip detection logic).
  1. Open or short in heated oxygen sensor (sensor 2) heater circuit
  2. Heated oxygen sensor (sensor 2)
  3. No. 1 integration relay
  4. ECM
P102A9E
Heated oxygen sensor heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
  1. Short in heated oxygen sensor (sensor 2) heater circuit
  2. ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.
  1. Heated Oxygen Sensor Heater Range Check (P003612, P003614 and P102A9E):
    1. The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.
    2. If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY


Frequency of Operation
Continuous

TYPICAL ENABLING CONDITIONS


Time after heater on
10 seconds or more

CONFIRMATION DRIVING PATTERN


A262623E05

  1. Connect the GTS to the DLC3.
  2. Turn the engine switch on (IG) and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the engine switch off and wait for at least 30 seconds.
  5. Turn the engine switch on (IG) and turn the GTS on [A].
  6. Start the engine and idle it for 5 minutes or more [B].
  7. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].
  8. Idle the engine for 5 minutes or more [D].
  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].
  10. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  12. Input the DTC: P003612, P003614 or P102A9E.
  13. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.


WIRING DIAGRAM

Refer to DTC P013613 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:
  1. Sensor 1 refers to the sensor closest to the engine assembly.
  2. Sensor 2 refers to the sensor farthest away from the engine assembly.
  3. Refer to "Data List / Active Test" [O2 Sensor Heater B1S2 and O2 Sensor Heater Current Value B1S2] (Click here).
  4. When the values for the Data List item O2 Sensor Heater Current Value B1S2 is not 0 A, the heater is on.
  5. Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the heated oxygen sensor output voltage . If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
  6. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
  1. Inspect the heated oxygen sensor (Click here).



NG
REPLACE HEATED OXYGEN SENSOR (Click here)
OK


2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR)


    A338418E01
  1. Disconnect the heated oxygen sensor connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Heated Oxygen Sensor)

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E21-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E21-1 (HT1B) - E96-17 (HT1B)
    Always
    Below 1 Ω
    E21-1 (HT1B) or E96-17 (HT1B) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P003612, P003614 OR P102A9E)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the engine switch off and wait for at least 30 seconds.

  1. Turn the engine switch on (IG).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTCs are not output
    A
    DTC P003612, P003614 or P102A9E is output
    B



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - HEATED OXYGEN SENSOR)
  1. Disconnect the heated oxygen sensor connector.

  1. Disconnect the No. 1 integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    1A-6 - E21-2 (+B)
    Always
    Below 1 Ω
    1A-6 or E21-2 (+B) - Body ground and other terminals
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)


    A256530E07
  1. Disconnect the No. 1 integration relay connector.
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Integration Relay)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1D-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY)
OK

REPLACE NO. 1 INTEGRATION RELAY (Click here)