DTC P010012 Mass or Volume Air Flow Sensor "A" Circuit Short to Battery |
DTC P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open |

| *1 | Mass Air Flow Meter Sub-assembly | - | - |
| *a | Silicon Chip Sensor | *b | By-pass Duct |
| *c | Heater | *d | Heater Thermistor |
| *e | Intake Air | *f | Temperature Sensor (After Heater) |
| *g | Temperature Sensor (Before Heater) | *h | Intake Air Thermistor 1 |
| *i | Intake Air Thermistor 2 | *j | Temperature Sensor (Before Heater) 1 |
| *k | Temperature Sensor (After Heater) 2 | *l | Temperature Sensor (After Heater) 1 |
| *m | Temperature Sensor (Before Heater) 2 | *n | Control Circuit |
| *o | Heater Control Bridge Circuit | *p | Temperature Sensor Bridge Circuit |
| *q | Air Flow | - | - |
| DTC No. | DTC Detection Condition | Trouble Area |
| P010012 | The mass air flow meter sub-assembly output frequency is higher than 9.8 kHz for 3 seconds or more (1 trip detection logic). |
|
| P010014 | The mass air flow meter sub-assembly output frequency is less than 0.1 kHz for 3 seconds or more (1 trip detection logic). |
|
| Frequency of Operation | Continuous |
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY) |
![]() |
Disconnect the mass air flow meter sub-assembly connector.
| *a | Front view of wire harness connector (to Mass Air Flow Meter Sub-assembly) |
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E105-3 (5V) - E105-2 (E2G) | Engine switch on (IG) | 4.8 to 5.2 V |
| E105-1 (FG) - E105-2 (E2G) | Engine switch on (IG) | 4.8 to 5.2 V |
|
| ||||
| OK | |
| 2.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P010012 OR P010014) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG) and turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P010012 or P010014 is output | A |
| DTCs are not output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E105-3 (5V) - E96-90 (VCVG) | Always | Below 1 Ω |
| E105-1 (FG) - E96-92 (VG) | Always | Below 1 Ω |
| E105-2 (E2G) - E96-91 (E2G) | Always | Below 1 Ω |
| E105-3 (5V) or E96-90 (VCVG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-1 (FG) or E96-92 (VG) - Body ground and other terminals | Always | 10 kΩ or higher |
| E105-2 (E2G) or E96-91 (E2G) - Body ground and other terminals | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||